diff --git a/LaunchProcedure.csv b/LaunchProcedure.csv index 9710559..26a17bb 100644 --- a/LaunchProcedure.csv +++ b/LaunchProcedure.csv @@ -1,4 +1,4 @@ -vers.;v4.7;Launch Procedure;;0;MRL;MCC;RdHill;Time per step; +vers.;v4.8;Launch Procedure;;0;MRL;MCC;RdHill;Time per step; 147:20;MCC;BEGIN SEQUENCE: Power on EGSE;Power on EGSE;1;;;;; 147:20;EGSE;Check CLD connection;;1;;;;; 147:20;EGSE;Switch ON CLD via Battery & check voltage (24 Volt);;1;;;;; @@ -11,14 +11,15 @@ vers.;v4.7;Launch Procedure;;0;MRL;MCC;RdHill;Time per step; 146:20;EGSE@MRL;Switch ON Bat_12V_10A & check voltage (ca. 13,8 Volt);;1;;;;; 146:20;EGSE@MRL;Switch ON Sup_24V_40A;;1;;;;; 146:20;EGSE@MRL;Switch ON Sup_5V_10A;;1;;;;03:00; -143:20;EGSE;Connect to cRIO;;1;;;;; -143:20;EGSE;Start FPGA_VI;;1;;;;; +143:20;EGSE;Connect to cRio;;1;;;;; +130:40;EGSE;Confirm storage capacity of cRio is greater than [!!!];;1;;;;00:10; 143:20;EGSE;Start RT_VI;;1;;;;; -143:20;EGSE;Confirm PID-VI is running;;1;;;;; +143:20;EGSE;Open PID-VI and confirm it is running;;1;;;;; 143:20;EGSE;Rename PID-Logfile;;1;;;;02:00; 141:20;MCC;BEGIN SEQUENCE: Connect Data Umbilical;Connect Data Umbilical;1;;;;00:30; -141:20;MRL;Confirm working Personel is grounded;;1;;;;; -141:20;EGSL@MRL;Confirm all 8 Groundingbridges are inserted;;1;;;;; +141:20;MRL;Confirm working personel is grounded;;1;;;;; +141:20;EGSL@MRL;Confirm ALL 8 Grounding bridges are inserted;;1;;;;; +141:20;EGSL@MRL;Connect Data Umbilical;;1;;;;; 140:50;EGSE;Turn on EPS_BAT;;1;;;;; 140:50;EGSE;Turn on EPS_EXT;;1;;;;; 140:50;EGSE@MRL;Leave EPS_BAT inserted and remove the other 7 Grounding Bridges;;1;;;;; @@ -31,7 +32,7 @@ vers.;v4.7;Launch Procedure;;0;MRL;MCC;RdHill;Time per step; 140:50;EGSE@MRL;Confirm Main bus LED is on.;;1;;;;; 140:50;EGSE;Start EPS via EPS_ext;;1;;;;; 140:50;OBDH;Clear SD-Card-using FileZilla FTP;;1;;;;01:00; -139:50;OBDH;Connect to sbRIO;;1;;;;; +139:50;OBDH;Connect to sbRio;;1;;;;; 139:50;OBDH;Start RT_Main;;1;;;;; 139:50;MRL;Confirm 3 beeps at OBC1;;1;;;;; 139:50;OBDH;Open RT_Sub_HMI;;1;;;;; @@ -39,7 +40,8 @@ vers.;v4.7;Launch Procedure;;0;MRL;MCC;RdHill;Time per step; 139:50;EGSE@MRL;Insert Payload Fuse;;1;;;;; 139:50;EGSE@MRL;Confirm green LED at Payload Fuse is on;;1;;;;; 139:50;MCC;BEGIN SEQUENCE: Connect Fueling arm;Connect Fueling Arm;1;;;;; -139:50;MRL;Confirm working Personel is grounded;;1;;;;01:00; +139:50;MRL;Confirm working personel is grounded;;1;;;;01:00; +139:50;MRL;Confirm PPG 0 bar;;1;;;;; 138:50;MRL;Remove Pneumatic Line from Fueling arm;;1;;;;; 138:50;MRL;Move Fueling arm to rocket;;1;;;;; 138:50;MRL;Couple Helium coupling;;1;;;;; @@ -60,8 +62,8 @@ vers.;v4.7;Launch Procedure;;0;MRL;MCC;RdHill;Time per step; 131:20;EGSE;Activate N2O_Heater 2;;1;;;;00:10; 131:10;EGSE;Activate He_Heater;;1;;;;00:10; 131:00;OBDH;Verify Heizi @ RDVT & RDVET;;1;;;;00:10; -130:50;EGSE/MRL;Verify Bottle Temperatures @ OxT1, OxT2, HPT2;;1;;;;00:10; -130:40;EGSE/MRL;Verify Water Temperatures @ Ox@T1, OxWT2, HPWT2;;1;;;;00:10; +130:50;EGSE/MRL;Check Bottle Temperatures @ OxT1, OxT2, HPT2. If above 30C aknowledge high temperature. If above 35C enter HOLD;;1;;;;00:10; +130:40;EGSE/MRL;Check Water Temperatures @ OxWT1, OxWT2, HPWT2;;1;;;;00:10; 130:30;EGSE;Deactivate Heizi;;1;;;;00:10; 130:20;EGSE;Check OxV1 (CLD & RT_VI);;1;;;;00:10; 130:10;EGSE;Check OxV2 (CLD & RT_VI);;1;;;;00:10; @@ -104,14 +106,14 @@ vers.;v4.7;Launch Procedure;;0;MRL;MCC;RdHill;Time per step; 113:00;EGSE@MRL;Plug in Bridges B1 and B2;;1;;;;; 113:00;MRL;Confirm Soundsignal from Ignition Umbilical;;1;;;;; 113:00;EGSE;Turn on Ignition Secure Switch;;1;;;;; -113:00;EGSE/OBDH;Turn on Ignition Switch for 2 Second & Confirm ignition signal received at sbRio;;1;;;;; -113:00;EGSE/OBDH;Confirm that Ignition Switch is switched off;;1;;;;; +113:00;EGSE/OBDH;Turn on Ignition Switch for 2 Second & Confirm ignition signal received at sbRio & cRio;;1;;;;; +113:00;EGSE;Confirm that Ignition Switch is switched OFF and secured;;1;;;;; 113:00;EGSE;Turn off Ignition Secure Switch;;1;;;;; 113:00;EGSE@MRL;Remove Bridges B1 and B2;;1;;;;; 113:00;MRL;Remove Ignition test receptical;;1;;;;03:00; -110:00;MCC;BEGIN SEQUENCE: pneumatic pressure test (PHASE YELLOW) ;Pneumatic Pressure Test;1;;;;; -110:00;EGSE/MRL;Verify Bottle Temperatures @ OxT1, OxT2, HPT2;;1;;;;00:10; -110:00;EGSE/MRL;Verify Water Temperatures @ Ox@T1, OxWT2, HPWT2;;1;;;;00:10; +110:00;MCC;BEGIN SEQUENCE: Ground segment pressure test (PHASE YELLOW) ;GSE Pressure Test;1;;;;; +130:50;EGSE/MRL;Check Bottle Temperatures @ OxT1, OxT2, HPT2. If above 30C aknowledge high temperature. If above 35C enter HOLD;;1;;;;00:10; +130:40;EGSE/MRL;Check Water Temperatures @ OxWT1, OxWT2, HPWT2;;1;;;;00:10; 110:00;MRL;Confirm that all hatches are closed;;1;;;;01:00; 109:00;MRL;Check He bottle 1 connector is attached;;1;;;;; 109:00;MRL;Check He bottle 2 connector is attached;;1;;;;; @@ -122,8 +124,9 @@ vers.;v4.7;Launch Procedure;;0;MRL;MCC;RdHill;Time per step; 109:00;MRL;Check hose between N2OSM & Flight Segment is connected on both ends;;1;;;;; 109:00;MRL;Check Pneumatik hose is connected on both ends;;1;;;;02:00; 107:00;MRL;Put on safety equipment;;2;;;;; -107:00;MRL;Move into Position to open He Bottle 1;;2;;;;; 107:00;MRL;Confirm MBV is closed;;2;;;;; +107:00;MRL;Confirm HPNV is closed;;2;;;;; +107:00;MRL;Move into Position to open He Bottle 1;;2;;;;; 107:00;EGSE;Confirm if HPV1 is closed;;2;;;;; 107:00;EGSE;Confirm MPV1/2 is closed;;2;;;;; 107:00;MRL;Open He Bottle 1;;2;;;;01:00; @@ -133,8 +136,8 @@ vers.;v4.7;Launch Procedure;;0;MRL;MCC;RdHill;Time per step; 106:00;MRL;Check pneumatic PPG (8 bar);;2;;;;; 106:00;MRL;Step back;;2;;;;01:00; 105:00;EGSE/MRL;Open & Close HPV1 SHORTLY & Check HPPT1;;2;;;;; -105:00;EGSE;Confirm HPPT1 is at 300 Bar;;2;;;;; -105:00;EGSE;Confirm HPLPT less than 10 Bar;;2;;;;; +105:00;EGSE;Check HPPT1 300 Bar;;2;;;;; +105:00;EGSE;Confirm HPLPT 0 Bar;;2;;;;; 105:00;EGSE/MRL;Open & Close HPV2 SHORTLY & Check HPPT2 0 bar;;2;;;;; 105:00;EGSE/MRL;Open & Close HPDV SHORTLY & Check HPLPT 0 bar;;2;;;;; 105:00;EGSE/MRL;Open & Close OxV1 SHORTLY;;2;;;;; @@ -146,16 +149,15 @@ vers.;v4.7;Launch Procedure;;0;MRL;MCC;RdHill;Time per step; 103:30;EGSE;Decouple Helium coupling;;2;;;;00:20; 103:10;EGSE;Move arm away from rocket;;2;;;;; 103:10;EGSE;Move arm to rocket;;2;;;;01:00; -102:10;MRL;Close He Bottle 1 and check HPSM for leakage (If leakage occurs Abort);;2;;;;01:00; -101:10;MRL;Open HPNV 1/8 Rev;;2;;;;; +102:10;MRL;Close He Bottle 1 and check HPSM for leakage (If leakage occurs continue with Passivation Procedure);;2;;;;01:00; 101:10;MRL;Open MBV;;2;;;;; 101:10;EGSE/MRL;Check and compare pressure HPPT1 with HPPG1 0 Bar;;2;;;;; 101:10;MRL;Close MBV;;2;;;;00:30; 100:40;MRL;Safety is ensured;;2;;;;; -100:40;MCC;MiS to MRL;;1;;;;; +100:40;MCC;EGSE@MRL to MRL;;1;;;;; 100:40;EGSE;Switch OFF N20 coupling;;1;;;;; 100:40;EGSE;Switch OFF He coupling;;1;;;;; -100:40;MRL;Confirm working Personel is grounded;;1;;;;01:00; +100:40;MRL;Confirm working personel is grounded;;1;;;;01:00; 100:40;MRL;Release Pneumatic lines of couplings;;1;;;;00:20; 100:20;EGSE;Confirm Fueling arm is switched OFF;;1;;;;; 100:20;EGSE;Check OxOutPT and HPLPT 0 bar;;1;;;;; @@ -163,12 +165,15 @@ vers.;v4.7;Launch Procedure;;0;MRL;MCC;RdHill;Time per step; 99:50;MRL;Couple N2O coupling;;1;;;;00:30; 99:50;MRL;Confirm He coupling is connected properly;;1;;;;; 99:50;MRL;Confirm N2O coupling is connected properly;;1;;;;; +130:50;EGSE/MRL;Check Bottle Temperatures @ OxT1, OxT2, HPT2. If above 30C aknowledge high temperature. If above 35C enter HOLD;;1;;;;00:10; +130:40;EGSE/MRL;Check Water Temperatures @ OxWT1, OxWT2, HPWT2;;1;;;;00:10; 99:20;MRL;HOLD;HOLD;1;;;;; -99:20;EGSE/MRL;Verify Bottle Temperatures @ OxT1, OxT2, HPT2;;1;;;;00:10; -99:20;EGSE/MRL;Verify Water Temperatures @ Ox@T1, OxWT2, HPWT2;;1;;;;00:10; 99:20;MCC;CONTINUE AFTER HOLD;;;;;;; -99:20;MRL;BEGIN SEQUENCE: Arming Rocket Part 1;Arming Rocket Pt.1;1;;;;; -99:20;MRL;Confirm working Personel is grounded;;1;;;;01:00; +130:50;EGSE/MRL;Check Bottle Temperatures @ OxT1, OxT2, HPT2. If above 30C aknowledge high temperature. If above 35C enter HOLD;;1;;;;00:10; +130:40;EGSE/MRL;Check Water Temperatures @ OxWT1, OxWT2, HPWT2;;1;;;;00:10; +99:20;MRL;BEGIN SEQUENCE: Prime Rocket;Prime Rocket;1;;;;; +99:20;EGSE;Turn ON EPS_BAT;;1;;;;01:00; +99:20;MRL;Confirm working personel is grounded;;1;;;;01:00; 99:20;MRL;Confirm all spring retracted hatches are moving freely;;1;;;;; 98:50;MRL;Turn on GoPro Camera at end of Launch Rail;;1;;;;00:20; 99:20;MRL;Connect Ignition Umbilical;;1;;;;00:30; @@ -176,12 +181,12 @@ vers.;v4.7;Launch Procedure;;0;MRL;MCC;RdHill;Time per step; 95:30;MRL;Confirm Bridge Hatch is Secured;;1;;;;00:20; 95:10;EGSE@MRL;return to MCC;;1;;;;; 95:10;OPS;Elevate MRL to 90 degrees;;1;;;;05:00; -90:10;EGSE;Powercycle EPS to to start flight mode on Telemega;;1;;;;00:30; 89:40;EGSE;Calibrate loadcell (Set to 0);;1;;;;01:00; 88:40;MCC;BEGIN SEQUENCE: Fueling Preparations (PHASE YELLOW);Fueling Preparations;2;;;;; -89:40;EGSE/MRL;Verify Bottle Temperatures @ OxT1, OxT2, HPT2;;1;;;;00:10; -89:40;EGSE/MRL;Verify Water Temperatures @ Ox@T1, OxWT2, HPWT2;;1;;;;00:10; +130:50;EGSE/MRL;Check Bottle Temperatures @ OxT1, OxT2, HPT2. If above 30C aknowledge high temperature. If above 35C enter HOLD;;1;;;;00:10; +130:40;EGSE/MRL;Check Water Temperatures @ OxWT1, OxWT2, HPWT2;;1;;;;00:10; 88:40;MRL;Put on safety equipment;;2;;;;00:30; +10:10;MRL;Open HPNV 1/8 Rev;;2;;;;; 88:10;MRL;Open He Bottle 1;;2;;;;01:00; 87:10;MRL;Step back;;2;;;;; 87:10;EGSE;Open & Close STEPWISE MPV1/MPV2 to 50 Bar @ OxInPT1 & OxInPT2;;2;;;;; @@ -198,27 +203,33 @@ vers.;v4.7;Launch Procedure;;0;MRL;MCC;RdHill;Time per step; 82:40;MRL/EGSE;Check & compare pressure OxInPT 2 with OxInPG 2 (max 50 bar);;2;;;;02:00; 80:40;MRL;Insert Ignition Bridges B1 and B2 into EGSE;;2;;;;02:00; 78:40;MRL;Confirm Soundsignal from Ignition Umbilical;;2;;;;; -78:40;MRL;Close ComTerm;;2;;;;; -78:40;MCC;Turn Off MRL lock;;2;;;;; -78:40;ALL;Clear Launchpad and inform OPS;;2;;;;10:00; -68:40;KLP;Start Camera Karsten Lappöhn;;2;;;;; +78:40;MRL;Close ComTerm & Go to Block House;;2;;;;; +78:40;MCC;Turn OFF MRL confirm lock;;2;;;;; +78:40;ALL;Inform OPS to clear Launch Pad (Tel.: [!!!]);;2;;;;2:00; +130:50;EGSE/MRL;Check Bottle Temperatures @ OxT1, OxT2, HPT2. If above 30C aknowledge high temperature. If above 35C enter HOLD;;1;;;;00:10; +130:40;EGSE/MRL;Check Water Temperatures @ OxWT1, OxWT2, HPWT2;;1;;;;00:10; 68:40;MCC;HOLD;HOLD;2;;;;; -68:40;EGSE;Verify Bottle Temperatures @ OxT1, OxT2, HPT2;;1;;;;00:10; -68:40;EGSE;Verify Water Temperatures @ Ox@T1, OxWT2, HPWT2;;1;;;;00:10; -68:40;MCC;CONTINUE AFTER HOLD;;;;;;; +68:40;KLP;Start Camera Karsten Lappöhn;;2;;;;; +68:40;MCC;CONTINUE AFTER HOLD;2;;;;;; +130:50;EGSE/MRL;Check Bottle Temperatures @ OxT1, OxT2, HPT2. If above 30C aknowledge high temperature. If above 35C enter HOLD;;1;;;;00:10; +130:40;EGSE/MRL;Check Water Temperatures @ OxWT1, OxWT2, HPWT2;;1;;;;00:10; +130:40;EGSE;Confirm storage capacity of CRio is greater than [!!!];;1;;;;00:10; 68:40;MCC;BEGIN SEQUENCE Ox Fueling (PHASE RED);Ox Fueling (PHASE RED);3;;;;; 68:40;MCC;Announce end of Radio Silence;;3;;;;; -68:40;OBDH/TMTC;Check RF451-Link;;1;;;;00:20; -68:40;TMTC;Confirm GPS-lock;;1;;;;00:20; -68:40;TMTC;Confirm Telemega-Link;;1;;;;00:20; -68:40;OBDH;Test Connection to STX3;;1;;;;00:20; -68:40;OBDH;Confirm that STX3 Package received by email;;1;;;;00:30; -68:40;MCC;Request Permission to begin fueling from OPS;;1;;;;03:00; +68:40;EGSE;Turn OFF EPS_BAT;;3;;;;; +126:50;OBDH/TMTC;Check RF451-Link;;1;;;;00:20; +126:30;TMTC;Confirm GPS-lock;;1;;;;00:20; +126:10;TMTC;Confirm Telemega-Link;;1;;;;00:20; +125:50;OBDH;Test Connection to STX3;;1;;;;00:20; +125:30;OBDH;Confirm that STX3 Package received by email;;1;;;;00:30; +125:30;AVC;Turn on main TMTC screen;;1;;;;00:30; +125:30;MCC;Request Permission to begin fueling from OPS;;1;;;;03:00; 68:40;OBDH;Acknowledge start of Fueling;;3;;;;01:00; -67:40;EGSE;Open & Close HPV1 STEPWISE to 50 Bar @ ROxTPT (stop at 30 bar and wait 30 seconds to check for leakage);;3;;;;; -67:40;EGSE;Open & Close HPV1 STEPWISE to more than 50 Bar @ RHPPT and check ROxTPT 50 Bar;;3;;;;; -67:40;EGSE;Check if HPV1 is closed;;3;;;;; -67:40;OBDH;Open RDV SHORTLY, to check tightness @ RHPPT & ROxTPT (If leakages occur Abort);;3;;;;; +67:40;EGSE;Open & Close HPV1 STEPWISE to 50 Bar @ ROxTPT (stop every 10 bar & check ROxTBT & ROxTTT (approx. ambiente temp);;3;;;;; +67:40;EGSE;Confirm OxOutPT 0 Bar to check ROxCV tightness;;3;;;;; +67:40;EGSE;Open & Close HPV1 STEPWISE to more than 50 Bar @ RHPPT and confirm ROxTPT 50 Bar;;3;;;;; +67:40;EGSE;Confirm HPV1 is closed;;3;;;;; +67:40;OBDH;Open RDV SHORTLY, to check tightness @ RHPPT & ROxTPT (If leakages occur continue with Abort Procedure);;3;;;;; 67:40;EGSE;Open MPV1/MPV2;;3;;;;; 67:40;EGSE;Open & Close MPV3 STEPWISE to 50 Bar @ OxOutPT;;3;;;;; 67:40;EGSE;Close MPV1/MPV2;;3;;;;; @@ -242,6 +253,7 @@ vers.;v4.7;Launch Procedure;;0;MRL;MCC;RdHill;Time per step; 11:20;OBDH;Check ROxCV for tightness @ ROxTPT;;3;;;;; 11:20;EGSE;Close OxDV;;3;;;;01:00; 10:20;EGSE;Write down OxTankMass;;3;;;;; +33:40;EGSE;Verify He Bottle 2 Temperature @HPT2 & @HPWT2 (turn ON He_Heater if necessary) ;;1;;;;00:10; 10:20;MCC;Provide OxTankMass and temperature readings to Wind weighting station;;3;;;;00:30; 9:50;EGSE;Confirm OxV1 & OxV2 closed;;3;;;;; 9:50;EGSE;Check OxOutPT 0 Bar;;3;;;;; @@ -250,30 +262,35 @@ vers.;v4.7;Launch Procedure;;0;MRL;MCC;RdHill;Time per step; 9:15;OBDH/TMTC;Check RF451-Link;;3;;;;00:20; 8:55;TMTC;Check GPS-lock;;3;;;;00:20; 8:35;TMTC;Check Telemega-Link;;3;;;;00:20; -8:15;MCC;HOLD;HOLD;3;;;;; +33:40;EGSE;Verify He Bottle 2 Temperature @HPT2 & @HPWT2 (turn ON/OFF He_Heater if necessary) ;;1;;;;00:10; +8:15;MCC;HOLD (Last possible scheduled HOLD);HOLD;3;;;;; 8:15;OPS;Align MRL to Launch Trajectory;;3;;;;; 8:15;MCC;Turn audio volume down;;3;;;;; -8:15;MCC;Turn off Confirm delay;;3;;;;; -8:15;ALL;Talk through Launch Sequence;;3;;;;; -8:15;MCC;Confirm MRL adjustment with OPS;;3;;;;; +8:15;MCC;Turn OFF ComTerm step delay;;3;;;;; +8:15;ALL;Talk through Ignition Sequence;;3;;;;; +8:15;MCC;Wait for OPS to confirm final MRL adjustment;;3;;;;; 8:15;AVC;Start Video recording in Block House;;3;;;;; 8:15;MCC;CONTINUE AFTER HOLD;;;;;;; -8:15;MCC;BEGIN Switching to Internal Power Sequence;Switch to Internal Power;3;;;;; -8:15;EGSE;Switch to internal Power;;3;;;;00:20; +8:15;EGSE;Verify He Bottle 2 Temperature @HPT2 & @HPWT2 (turn ON/OFF He_Heater if necessary) ;;1;;;;00:10; +8:15;MCC;BEGIN SEQUENCE: Switching to Internal Power Sequence;Switch to Internal Power;3;;;;; +8:15;EGSE;Turn OFF EPS_Ext (Switch to internal Power);;3;;;;00:20; 7:55;OBDH;Confirm EPS Voltages are within limits;;3;;;;00:10; 7:45;OBDH;Confirm RF451 Transmitting;;3;;;;00:05; 7:40;OBDH/TMTC;Confirm RF451-Link;;3;;;;00:20; 7:20;TMTC;Confirm GPS-lock;;3;;;;00:20; 7:00;TMTC;Confirm Telemega-Link;;3;;;;00:20; -6:40;OBDH;Switch to PREAMRED;;3;;;;00:10; +6:40;OBDH;Switch to PREARMED;;3;;;;00:10; 6:30;PYL;Confirm Payload is running;;3;;;;00:20; +6:30;PYL;Confirm BlackBox2 is ready for launch;;3;;;;; 6:10;AVC;Confirm that videorecording @ MCC is running;;3;;;;00:05; 6:05;MCC;BEGIN SEQUENCE: High Pressure Fueling;High Pressure Fueling;3;;;;; +33:40;EGSE;Verify He Bottle 2 Temperature @HPT2 & @HPWT2 (turn ON/OFF He_Heater if necessary) ;;1;;;;00:10; 6:05;EGSE;Open & Close HPV1 STEPWISE until RHPPT 300 Bar or pressure equal to He Bottle 1;;3;;;;; 6:05;EGSE;Open & Close HPV2 STEPWISE until RHPPT 300 Bar ;;3;;;;; 6:05;EGSE;Open & close HPDV STEPWISE until HPLPT 0 Bar ;;3;;;;; 6:05;EGSE;Confirm HPDV closed;;3;;;;; 6:05;OBDH/EGSE;Check for leakage & HPLPT 0 Bar & RHPPT 300 Bar ;;3;;;;02:00; +6:05;EGSE;Turn OFF He_Heater;;3;;;;; 4:05;OBDH;Acknowledge end of Fueling;;3;;;;00:10; 3:55;MCC;Confirm End of Fueling to OPS;;3;;;;00:20; 3:35;MCC;BEGIN SEQUENCE: Disconnecting Fueling Arm;Disconnecting Fueling Arm;3;;;;00:10; @@ -289,10 +306,10 @@ vers.;v4.7;Launch Procedure;;0;MRL;MCC;RdHill;Time per step; 1:10;MCC;Set Go/No-Go System to Go;;3;;;;00:10; 1:00;MCC;Wait for Authorization for Launch;;3;;;;00:00; 1:00;MCC;BEGIN SEQUENCE: Ignition;Ignition Sequence;4;;;;00:10; -0:50;OBDH;ARM;;4;;;;00:05; -0:45;OBDH;Confirm all status indicators green;;4;;;;00:05; -0:40;OBDH;Disconnect Ethernet;;4;;;;00:30; -0:10;EGSE;Turn on Ignition Secure;;4;;;;00:07; +0:50;OBDH;T-50 ARM;;4;;;;00:05; +0:40;OBDH;T-40 Confirm all status indicators green;;4;;;;00:05; +0:30;OBDH;T-30 Disconnect from sbRio;;4;;;;00:30; +0:10;EGSE;T-10 Turn on Ignition Secure;;4;;;;00:07; 0:03;EGSE;T-3: Ignition;;4;;;;00:03; 0:00;OBDH;T+0: Verify RMOxOV Open (Launched);;4;;;;00:00; 0:00;EGSE;T+1: Turn OFF Ignition;;4;;;;; @@ -304,8 +321,8 @@ vers.;v4.7;Launch Procedure;;0;MRL;MCC;RdHill;Time per step; 0:00;MCC;BEGIN SEQUENCE: PASSIVATION (PHASE YELLOW) (Write down Time);Passivation;2;;;;; 68:40;MCC;Announce BEGIN of Radio Silence;;3;;;;; 0:00;MCC;Turn audio volume up;;2;;;;; -0:00;TMTC;Check ROxTPT & RHPPT 1 Bar, if more: Open & Close STEPWISE RDV;;2;;;;; -0:00;MRL;Go to Testrig, Close N2O Bottle 1 & N2O Bottle 2 then RETURN to Block House;;2;;;;; +0:00;MRL;Go to MRL, Close N2O Bottle 1 & N2O Bottle 2, THEN... RETURN to Block House;;2;;;;; +0:00;MRL;RETURN to Block House;;2;;;;; 0:00;EGSE;Open OxDV;;2;;;;; 0:00;EGSE;Open OxV1;;2;;;;; 0:00;EGSE;Check OxInPT1 & OxOutPT 0 Bar;;2;;;;; @@ -345,7 +362,9 @@ vers.;v4.7;Launch Procedure;;0;MRL;MCC;RdHill;Time per step; 0:00;AVC;Turn off GoPro & Camcorder & Stop Block House Video recording;;1;;;;; 0:00;EGSE;Copy PID.vi.tdms & save to new name;;1;;;;; 0:00;EGSE;Wait for buffer storage process to be finished;;1;;;;; -0:00;EGSE;save data files from cRIO to PC;;1;;;;; +0:00;EGSE;save data files from cRio to PC;;1;;;;; +0:00;WIND;Save data on external HDD;;1;;;;; +0:00;TMTC;Stop TMTC Vi and save data on external HDD;;1;;;;; 0:00;AVC;End audio recording;;1;;;;; 0:00;MCC;Stop ComTerm and save logfile to external HDD, THEN...;;1;;;;; 0:00;MCC;Restart ComTerm VI;;1;;;;;