diff --git a/LaunchProcedure.csv b/LaunchProcedure.csv
index fe6b770..e12165b 100644
--- a/LaunchProcedure.csv
+++ b/LaunchProcedure.csv
@@ -1,17 +1,17 @@
-vers.;v4.10;Launch Procedure;;0;MRL;MCC;RdHill;Time per step;
+vers.;v4.13;Launch Procedure;;0;MRL;MCC;RdHill;Time per step;
 147:20;WIND;Start wind weighting analysis;;1;;;;;
 147:20;MCC;BEGIN SEQUENCE: Power on EGSE;Power on EGSE;1;;;;;
 147:20;EGSE;Check CLD connection;;1;;;;;
 147:20;EGSE;Switch ON CLD via Battery & check voltage (24 Volt);;1;;;;;
 147:20;EGSE;Switch ON the primary and secondary supply switches on the Control Panel;;1;;;;01:00;
-146:20;EGSE@MRL;Switch ON Sup_24V_20A & check voltage (ca. 27,2 Volt);;1;;;;;
-146:20;EGSE@MRL;Switch ON Sup_24V_10A & check voltage (ca. 27,2 Volt);;1;;;;;
-146:20;EGSE@MRL;Switch ON Sup_12V_10A & check voltage (ca. 13,8 Volt);;1;;;;;
-146:20;EGSE@MRL;Switch ON Bat_24V_20A & check voltage (ca. 27,9 Volt);;1;;;;;
-146:20;EGSE@MRL;Switch ON Bat_24V_10A & check voltage (ca. 27,9 Volt);;1;;;;;
-146:20;EGSE@MRL;Switch ON Bat_12V_10A & check voltage (ca. 13,8 Volt);;1;;;;;
-146:20;EGSE@MRL;Switch ON Sup_24V_40A;;1;;;;;
-146:20;EGSE@MRL;Switch ON Sup_5V_10A;;1;;;;03:00;
+146:20;EGSE @MRL;Switch ON Sup_24V_20A & check voltage (ca. 27,2 Volt);;1;;;;;
+146:20;EGSE @MRL;Switch ON Sup_24V_10A & check voltage (ca. 27,2 Volt);;1;;;;;
+146:20;EGSE @MRL;Switch ON Sup_12V_10A & check voltage (ca. 13,8 Volt);;1;;;;;
+146:20;EGSE @MRL;Switch ON Bat_24V_20A & check voltage (ca. 27,9 Volt);;1;;;;;
+146:20;EGSE @MRL;Switch ON Bat_24V_10A & check voltage (ca. 27,9 Volt);;1;;;;;
+146:20;EGSE @MRL;Switch ON Bat_12V_10A & check voltage (ca. 13,8 Volt);;1;;;;;
+146:20;EGSE @MRL;Switch ON Sup_24V_40A;;1;;;;;
+146:20;EGSE @MRL;Switch ON Sup_5V_10A;;1;;;;03:00;
 143:20;EGSE;Connect to cRio;;1;;;;;
 130:40;EGSE;Confirm storage capacity of cRio is greater than [!!!];;1;;;;00:10;
 143:20;EGSE;Start RT_VI;;1;;;;;
@@ -19,18 +19,18 @@ vers.;v4.10;Launch Procedure;;0;MRL;MCC;RdHill;Time per step;
 143:20;EGSE;Rename PID-Logfile;;1;;;;02:00;
 141:20;MCC;BEGIN SEQUENCE: Connect Data Umbilical;Connect Data Umbilical;1;;;;00:30;
 141:20;MRL;Confirm working personel is grounded;;1;;;;;
-141:20;EGSL@MRL;Confirm ALL 8 Grounding bridges are inserted;;1;;;;;
-141:20;EGSL@MRL;Connect Data Umbilical;;1;;;;;
+141:20;EGSL @MRL;Confirm ALL 8 Grounding bridges are inserted;;1;;;;;
+141:20;EGSL @MRL;Connect Data Umbilical;;1;;;;;
 140:50;EGSE;Turn on EPS_BAT;;1;;;;;
 140:50;EGSE;Turn on EPS_EXT;;1;;;;;
-140:50;EGSE@MRL;Leave EPS_BAT inserted and remove the other 7 Grounding Bridges;;1;;;;;
-140:50;EGSE@MRL;Insert EPS_EXT Fuse in Power Supply Control Panel;;1;;;;;
-140:50;EGSE@MRL;Confirm green LED at EPS_EXT Fuse is on;;1;;;;;
-140:50;EGSE@MRL;Insert Main_Bus Fuse in Power Supply Control Panel;;1;;;;;
-140:50;EGSE@MRL;Confirm LED at Main_Bus Fuse is OFF. Else Pull fuse and insert all Grounding Bridges;;1;;;;;
-140:50;EGSE@MRL;Set remaining Fuses (except Payload Fuse) and check for green LED;;1;;;;;
+140:50;EGSE @MRL;Leave EPS_BAT inserted and remove the other 7 Grounding Bridges;;1;;;;;
+140:50;EGSE @MRL;Insert EPS_EXT Fuse in Power Supply Control Panel;;1;;;;;
+140:50;EGSE @MRL;Confirm green LED at EPS_EXT Fuse is on;;1;;;;;
+140:50;EGSE @MRL;Insert Main_Bus Fuse in Power Supply Control Panel;;1;;;;;
+140:50;EGSE @MRL;Confirm LED at Main_Bus Fuse is OFF. Else Pull fuse and insert all Grounding Bridges;;1;;;;;
+140:50;EGSE @MRL;Set remaining Fuses (except Payload Fuse) and check for green LED;;1;;;;;
 140:50;EGSE;Turn OFF EPS_BAT;;1;;;;;
-140:50;EGSE@MRL;Confirm Main bus LED is on.;;1;;;;;
+140:50;EGSE @MRL;Confirm Main bus LED is on.;;1;;;;;
 140:50;EGSE;Start EPS via EPS_ext;;1;;;;;
 140:50;OBDH;Clear SD-Card-using FileZilla FTP;;1;;;;01:00;
 139:50;OBDH;Connect to sbRio;;1;;;;;
@@ -38,8 +38,8 @@ vers.;v4.10;Launch Procedure;;0;MRL;MCC;RdHill;Time per step;
 139:50;MRL;Confirm 3 beeps at OBC1;;1;;;;;
 139:50;OBDH;Open RT_Sub_HMI;;1;;;;;
 139:50;OBDH;Confirm Main Chute button is disabled;;1;;;;;
-139:50;EGSE@MRL;Insert Payload Fuse;;1;;;;;
-139:50;EGSE@MRL;Confirm green LED at Payload Fuse is on;;1;;;;;
+139:50;EGSE @MRL;Insert Payload Fuse;;1;;;;;
+139:50;EGSE @MRL;Confirm green LED at Payload Fuse is on;;1;;;;;
 139:50;WIND;Report on weather situation;;1;;;;;
 139:50;MCC;BEGIN SEQUENCE: Connect Fueling arm;Connect Fueling Arm;1;;;;;
 139:50;MRL;Confirm working personel is grounded;;1;;;;01:00;
@@ -56,17 +56,17 @@ vers.;v4.10;Launch Procedure;;0;MRL;MCC;RdHill;Time per step;
 135:30;EGSE;Start PID data recording;;1;;;;00:10;
 135:20;MRL;Close HPNV 1;;1;;;;00:10;
 135:20;MRL;Close HPNV 2;;1;;;;00:10;
-135:10;EGSE/MRL;Switch OxDV to closed & check if magnetic valve LED is on;;1;;;;00:10;
-135:00;EGSE/MRL;Switch HPDV to closed & check if magnetic valve LED is on;;1;;;;00:10;
-134:50;EGSE/MRL;Check warning lamp on HPSM;;1;;;;00:10;
+135:10;EGSE/ MRL;Switch OxDV to closed & check if magnetic valve LED is on;;1;;;;00:10;
+135:00;EGSE/ MRL;Switch HPDV to closed & check if magnetic valve LED is on;;1;;;;00:10;
+134:50;EGSE/ MRL;Check warning lamp on HPSM;;1;;;;00:10;
 134:40;MRL;Remove loose equipment;;1;;;;03:00;
 131:40;EGSE;Activate Heizi;;1;;;;00:10;
 131:30;EGSE;Activate N2O_Heater 1;;1;;;;00:10;
 131:20;EGSE;Activate N2O_Heater 2;;1;;;;00:10;
 131:10;EGSE;Activate He_Heater;;1;;;;00:10;
 131:00;OBDH;Verify Heizi @ RDVT & RDVET;;1;;;;00:10;
-130:50;EGSE/MRL;Check Bottle Temperatures @ OxT1, OxT2, HPT2. If above 30C aknowledge high temperature. If above 35C enter HOLD;;1;;;;00:10;
-130:40;EGSE/MRL;Check Water Temperatures @ OxWT1, OxWT2, HPWT2;;1;;;;00:10;
+130:50;EGSE/ MRL;Check Bottle Temperatures @ OxT1, OxT2, HPT2. If above 30C aknowledge high temperature. If above 35C enter HOLD;;1;;;;00:10;
+130:40;EGSE/ MRL;Check Water Temperatures @ OxWT1, OxWT2, HPWT2;;1;;;;00:10;
 130:30;EGSE;Deactivate Heizi;;1;;;;00:10;
 130:20;EGSE;Check OxV1 (CLD & RT_VI);;1;;;;00:10;
 130:10;EGSE;Check OxV2 (CLD & RT_VI);;1;;;;00:10;
@@ -86,7 +86,7 @@ vers.;v4.10;Launch Procedure;;0;MRL;MCC;RdHill;Time per step;
 127:00;OBDH;Confirm RNCEV is disabled;;1;;;;00:10;
 125:00;MRL;Confirm MBV closed;;1;;;;;
 125:00;EGSE;Confirm that all valve switches are in OFF position (Except OxDV & HPDV);;1;;;;0:10;
-115:00;MRL/EGSE;Check loadcell by applying force to it;;1;;;;00:20;
+115:00;MRL/ EGSE;Check loadcell by applying force to it;;1;;;;00:20;
 114:40;OBDH;Check RHPPT shows atmosphere;;1;;;;;
 114:40;OBDH;Check ROxTPT shows atmosphere;;1;;;;;
 114:40;OBDH;Check RIHPT shows atmosphere;;1;;;;;
@@ -99,24 +99,24 @@ vers.;v4.10;Launch Procedure;;0;MRL;MCC;RdHill;Time per step;
 114:20;EGSE;Check OxInPT1 shows 0 bar;;1;;;;;
 114:20;EGSE;Check OxInPT2 shows 0 bar;;1;;;;;
 114:20;EGSE;Check OxOutPT shows 0 bar;;1;;;;00:20;
-114:00;EGSE/MRL;Switch on N2O coupling & check if magnetic valve LED is on;;1;;;;;
-114:00;EGSE/MRL;Switch on He coupling & check if magnetic valve LED is on;;1;;;;;
-114:00;EGSE/MRL;Switch on swivle arm & check if magnetic valve LED is on;;1;;;;;
+114:00;EGSE/ MRL;Switch on N2O coupling & check if magnetic valve LED is on;;1;;;;;
+114:00;EGSE/ MRL;Switch on He coupling & check if magnetic valve LED is on;;1;;;;;
+114:00;EGSE/ MRL;Switch on swivle arm & check if magnetic valve LED is on;;1;;;;;
 114:00;EGSE;Switch off swivel arm & He coupling & N2O coupling;;1;;;;01:00;
 114:00;MCC;BEGIN SEQUENCE: Ignition signal Test;Ignition signal Test;1;;;;01:00;
 113:00;MRL;Confirm that Ignition Umbilical is disconnected;;1;;;;;
 113:00;MRL;Connect Ignition test receptical;;1;;;;;
-113:00;EGSE@MRL;Plug in Bridges B1 and B2;;1;;;;;
+113:00;EGSE @MRL;Plug in Bridges B1 and B2;;1;;;;;
 113:00;MRL;Confirm Soundsignal from Ignition Umbilical;;1;;;;;
 113:00;EGSE;Turn on Ignition Secure Switch;;1;;;;;
-113:00;EGSE/OBDH;Turn on Ignition Switch for 2 Second & Confirm ignition signal received at sbRio & cRio;;1;;;;;
+113:00;EGSE/ OBDH;Turn on Ignition Switch for 2 Second & Confirm ignition signal received at sbRio & cRio;;1;;;;;
 113:00;EGSE;Confirm that Ignition Switch is switched OFF and secured;;1;;;;;
 113:00;EGSE;Turn off Ignition Secure Switch;;1;;;;;
-113:00;EGSE@MRL;Remove Bridges B1 and B2;;1;;;;;
+113:00;EGSE @MRL;Remove Bridges B1 and B2;;1;;;;;
 113:00;MRL;Remove Ignition test receptical;;1;;;;03:00;
-110:00;MCC;BEGIN SEQUENCE: Ground segment pressure test (PHASE YELLOW) ;GSE Pressure Test;1;;;;;
-130:50;EGSE/MRL;Check Bottle Temperatures @ OxT1, OxT2, HPT2. If above 30C aknowledge high temperature. If above 35C enter HOLD;;1;;;;00:10;
-130:40;EGSE/MRL;Check Water Temperatures @ OxWT1, OxWT2, HPWT2;;1;;;;00:10;
+110:00;MCC;BEGIN SEQUENCE: Ground segment pressure test (PHASE YELLOW) ;GSE Pressure Test;1;LuF, AlS, LeD: 1x Helm, 3x Ear protectors;ChB, FiH, JuL, LiA, MiS;;;
+130:50;EGSE/ MRL;Check Bottle Temperatures @ OxT1, OxT2, HPT2. If above 30C aknowledge high temperature. If above 35C enter HOLD;;1;;;;00:10;
+130:40;EGSE/ MRL;Check Water Temperatures @ OxWT1, OxWT2, HPWT2;;1;;;;00:10;
 110:00;MRL;Confirm that all hatches are closed;;1;;;;01:00;
 109:00;MRL;Check He bottle 1 connector is attached;;1;;;;;
 109:00;MRL;Check He bottle 2 connector is attached;;1;;;;;
@@ -139,15 +139,15 @@ vers.;v4.10;Launch Procedure;;0;MRL;MCC;RdHill;Time per step;
 106:00;MRL;Check Harris PPR (50 to 8 bar);;2;;;;;
 106:00;MRL;Check pneumatic PPG (8 bar);;2;;;;;
 106:00;MRL;Step back;;2;;;;01:00;
-105:00;EGSE/MRL;Open & Close HPV1 SHORTLY & Check HPPT1;;2;;;;;
+105:00;EGSE/ MRL;Open & Close HPV1 SHORTLY & Check HPPT1;;2;;;;;
 105:00;EGSE;Check HPPT1 300 Bar;;2;;;;;
 105:00;EGSE;Confirm HPLPT 0 Bar;;2;;;;;
-105:00;EGSE/MRL;Open & Close HPV2 SHORTLY & Check HPPT2 0 bar;;2;;;;;
-105:00;EGSE/MRL;Open & Close HPDV SHORTLY & Check HPLPT 0 bar;;2;;;;;
-105:00;EGSE/MRL;Open & Close OxV1 SHORTLY;;2;;;;;
-105:00;EGSE/MRL;Open & Close OxV2 SHORTLY;;2;;;;;
-105:00;EGSE/MRL;Open & Close OxDV SHORTLY;;2;;;;;
-105:00;EGSE/MRL;Open & Close MPV3 SHORTLY;;2;;;;;
+105:00;EGSE/ MRL;Open & Close HPV2 SHORTLY & Check HPPT2 0 bar;;2;;;;;
+105:00;EGSE/ MRL;Open & Close HPDV SHORTLY & Check HPLPT 0 bar;;2;;;;;
+105:00;EGSE/ MRL;Open & Close OxV1 SHORTLY;;2;;;;;
+105:00;EGSE/ MRL;Open & Close OxV2 SHORTLY;;2;;;;;
+105:00;EGSE/ MRL;Open & Close OxDV SHORTLY;;2;;;;;
+105:00;EGSE/ MRL;Open & Close MPV3 SHORTLY;;2;;;;;
 00:00;MRL;Open HPNV1;;2;;;;;;
 10:10;MRL;????!!!!DO NOT EXECUTE BEFORE DISCUSSION!!!!!Open HPNV2 1/8 Rev;;2;;;;;
 00:00;MRL;Step Back;;2;;;;;;
@@ -160,8 +160,8 @@ vers.;v4.10;Launch Procedure;;0;MRL;MCC;RdHill;Time per step;
 00:00;EGSE;Open HPV2 & confirm HPPT2 0 Bar;;2;;;;;
 00:00;EGSE;Close HPV2;;2;;;;;
 00:00;EGSE;Close HPDV;;2;;;;;
-87:10;EGSE;Open & Close STEPWISE MPV1/MPV2 to 50 Bar @ OxInPT1 & OxInPT2;;2;;;;;
-87:10;EGSE;Confirm MPV1/MPV2 closed;;2;;;;;
+87:10;EGSE;Open & Close STEPWISE MPV1/2 to 50 Bar @ OxInPT1 & OxInPT2;;2;;;;;
+87:10;EGSE;Confirm MPV1/2 closed;;2;;;;;
 87:10;EGSE;Open OxDV;;2;;;;;
 87:10;EGSE;Open & Close STEPWISE MPV3 to 0 Bar @OxOutPT;;2;;;;;
 87:10;EGSE;Check OxInPT1 and OxInPT2 for leakage (If leakage occurs proceed to "GSE passivation Procedure";;2;;;;;
@@ -177,12 +177,12 @@ vers.;v4.10;Launch Procedure;;0;MRL;MCC;RdHill;Time per step;
 103:10;EGSE;Move arm to rocket;;2;;;;01:00;
 102:10;MRL;Close He Bottle 1 and check HPSM for leakage (If leakage occurs continue with Passivation Procedure);;2;;;;01:00;
 101:10;MRL;Open MBV;;2;;;;;
-101:10;EGSE/MRL;Check and compare pressure HPPT1 with HPPG1 0 Bar;;2;;;;;
+101:10;EGSE/ MRL;Check and compare pressure HPPT1 with HPPG1 0 Bar;;2;;;;;
 101:10;MRL;Close MBV;;2;;;;00:30;
 100:40;MRL;Open RMDV & relief pressure;;2;;;;;
 100:40;MRL;Close RMDV;;2;;;;;
 100:40;MRL;Safety is ensured;;2;;;;;
-100:40;MCC;EGSE@MRL to MRL;;1;;;;;
+100:40;MCC;EGSE @MRL to MRL;;1;;;;;
 100:40;EGSE;Switch OFF N20 coupling;;1;;;;;
 100:40;EGSE;Switch OFF He coupling;;1;;;;;
 100:40;MRL;Confirm working personel is grounded;;1;;;;01:00;
@@ -194,12 +194,12 @@ vers.;v4.10;Launch Procedure;;0;MRL;MCC;RdHill;Time per step;
 99:50;MRL;Couple N2O coupling;;1;;;;00:30;
 99:50;MRL;Confirm He coupling is connected properly;;1;;;;;
 99:50;MRL;Confirm N2O coupling is connected properly;;1;;;;;
-130:50;EGSE/MRL;Check Bottle Temperatures @ OxT1, OxT2, HPT2. If above 30C aknowledge high temperature. If above 35C enter HOLD;;1;;;;00:10;
-130:40;EGSE/MRL;Check Water Temperatures @ OxWT1, OxWT2, HPWT2;;1;;;;00:10;
+130:50;EGSE/ MRL;Check Bottle Temperatures @ OxT1, OxT2, HPT2. If above 30C aknowledge high temperature. If above 35C enter HOLD;;1;;;;00:10;
+130:40;EGSE/ MRL;Check Water Temperatures @ OxWT1, OxWT2, HPWT2;;1;;;;00:10;
 99:20;MRL;HOLD;HOLD;1;;;;;
 99:20;MCC;CONTINUE AFTER HOLD;;;;;;;
-130:50;EGSE/MRL;Check Bottle Temperatures @ OxT1, OxT2, HPT2. If above 30C aknowledge high temperature. If above 35C enter HOLD;;1;;;;00:10;
-130:40;EGSE/MRL;Check Water Temperatures @ OxWT1, OxWT2, HPWT2;;1;;;;00:10;
+130:50;EGSE/ MRL;Check Bottle Temperatures @ OxT1, OxT2, HPT2. If above 30C aknowledge high temperature. If above 35C enter HOLD;;1;;;;00:10;
+130:40;EGSE/ MRL;Check Water Temperatures @ OxWT1, OxWT2, HPWT2;;1;;;;00:10;
 99:20;MRL;BEGIN SEQUENCE: Prime Rocket;Prime Rocket;1;;;;;
 99:20;EGSE;Turn ON EPS_BAT;;1;;;;01:00;
 99:20;MRL;Confirm working personel is grounded;;1;;;;01:00;
@@ -208,12 +208,12 @@ vers.;v4.10;Launch Procedure;;0;MRL;MCC;RdHill;Time per step;
 99:20;MRL;Connect Ignition Umbilical;;1;;;;00:30;
 98:30;MRL;Insert all EPS Bridges;;1;;;;03:00;
 95:30;MRL;Confirm Bridge Hatch is Secured;;1;;;;00:20;
-95:10;EGSE@MRL;return to MCC;;1;;;;;
+95:10;EGSE @MRL;return to MCC;;1;;;;;
 95:10;OPS;Elevate MRL to 90 degrees;;1;;;;05:00;
 89:40;EGSE;Calibrate loadcell (Set to 0);;1;;;;01:00;
 88:40;MCC;BEGIN SEQUENCE: Fueling Preparations (PHASE YELLOW);Fueling Preparations;2;;;;;
-130:50;EGSE/MRL;Check Bottle Temperatures @ OxT1, OxT2, HPT2. If above 30C aknowledge high temperature. If above 35C enter HOLD;;1;;;;00:10;
-130:40;EGSE/MRL;Check Water Temperatures @ OxWT1, OxWT2, HPWT2;;1;;;;00:10;
+130:50;EGSE/ MRL;Check Bottle Temperatures @ OxT1, OxT2, HPT2. If above 30C aknowledge high temperature. If above 35C enter HOLD;;1;;;;00:10;
+130:40;EGSE/ MRL;Check Water Temperatures @ OxWT1, OxWT2, HPWT2;;1;;;;00:10;
 127:40;OBDH;Check RDV;;1;;;;00:10;
 127:30;OBDH;Check RNCEV;;1;;;;00:10;
 127:20;OBDH;Check RMOxOV;;1;;;;00:10;
@@ -233,37 +233,37 @@ vers.;v4.10;Launch Procedure;;0;MRL;MCC;RdHill;Time per step;
 00:00;EGSE;Confirm HPV2 is closed;;2;;;;;
 10:10;MRL;Open HPNV2 1/8 Rev;;2;;;;;
 00:00;EGSE;Close HPDV;;2;;;;;
-87:10;EGSE;Open & Close STEPWISE MPV1/MPV2 to 50 Bar @ OxInPT1 & OxInPT2;;2;;;;;
-87:10;EGSE/MRL;Check & compare OxInPT1 with OxInPG1 based on Bottle temperature (max 50 bar);;2;;;;;
-87:10;EGSE/MRL;Check & compare pressure OxInPT2 with OxInPG2 based on Bottle temperature (max 50 bar);;2;;;;;
-87:10;EGSE/MRL;Check Temperature of N2O Bottle 1 @OxT1 & OxWT1 (max 22C);;2;;;;;
-87:10;EGSE/MRL;Check Temperature of N2O Bottle 2 @OxT2 & OxWT2 (max 22C);;2;;;;01:30;
+87:10;EGSE;Open & Close STEPWISE MPV1/2 to 50 Bar @ OxInPT1 & OxInPT2;;2;;;;;
+87:10;EGSE/ MRL;Check & compare OxInPT1 with OxInPG1 based on Bottle temperature (max 50 bar);;2;;;;;
+87:10;EGSE/ MRL;Check & compare pressure OxInPT2 with OxInPG2 based on Bottle temperature (max 50 bar);;2;;;;;
+87:10;EGSE/ MRL;Check Temperature of N2O Bottle 1 @OxT1 & OxWT1 (max 22C);;2;;;;;
+87:10;EGSE/ MRL;Check Temperature of N2O Bottle 2 @OxT2 & OxWT2 (max 22C);;2;;;;01:30;
 85:40;MRL;Open He Bottle 2;;2;;;;;
-85:40;EGSE/MRL;Check & compare pressure HPPT2 with HPPG2 (max 315 bar);;2;;;;01:00;
-84:40;ALL/MRL;CAUTION!;;2;;;;;
+85:40;EGSE/ MRL;Check & compare pressure HPPT2 with HPPG2 (max 315 bar);;2;;;;01:00;
+84:40;ALL/ MRL;CAUTION!;;2;;;;;
 84:40;MRL;Open N2O Bottle 1;;2;;;;;
-84:40;MRL/EGSE;Check & compare pressure OxInPT 1 with OxInPG 1 (max 50 bar);;2;;;;02:00;
+84:40;MRL/ EGSE;Check & compare pressure OxInPT 1 with OxInPG 1 (max 50 bar);;2;;;;02:00;
 82:40;MRL;Open N2O Bottle 2;;2;;;;;
-82:40;MRL/EGSE;Check & compare pressure OxInPT 2 with OxInPG 2 (max 50 bar);;2;;;;02:00;
+82:40;MRL/ EGSE;Check & compare pressure OxInPT 2 with OxInPG 2 (max 50 bar);;2;;;;02:00;
 80:40;MRL;Insert Ignition Bridges B1 and B2 into EGSE;;2;;;;02:00;
 78:40;MRL;Confirm Soundsignal from Ignition Umbilical;;2;;;;;
 78:40;MRL;Close ComTerm & Go to Block House;;2;;;;;
 78:40;MCC;Turn OFF MRL confirm lock;;2;;;;;
 78:40;ALL;Inform OPS to clear Launch Pad (Tel.: [!!!]);;2;;;;2:00;
 147:20;WIND;Start wind weighting analysis;;1;;;;;
-130:50;EGSE/MRL;Check Bottle Temperatures @ OxT1, OxT2, HPT2. If above 30C aknowledge high temperature. If above 35C enter HOLD;;1;;;;00:10;
-130:40;EGSE/MRL;Check Water Temperatures @ OxWT1, OxWT2, HPWT2;;1;;;;00:10;
+130:50;EGSE/ MRL;Check Bottle Temperatures @ OxT1, OxT2, HPT2. If above 30C aknowledge high temperature. If above 35C enter HOLD;;1;;;;00:10;
+130:40;EGSE/ MRL;Check Water Temperatures @ OxWT1, OxWT2, HPWT2;;1;;;;00:10;
 68:40;MCC;HOLD;HOLD;2;;;;;
 68:40;KLP;Start Camera Karsten Lappöhn;;2;;;;;
 68:40;MCC;CONTINUE AFTER HOLD;2;;;;;;
-130:50;EGSE/MRL;Check Bottle Temperatures @ OxT1, OxT2, HPT2. If above 30C aknowledge high temperature. If above 35C enter HOLD;;1;;;;00:10;
-130:40;EGSE/MRL;Check Water Temperatures @ OxWT1, OxWT2, HPWT2;;1;;;;00:10;
+130:50;EGSE/ MRL;Check Bottle Temperatures @ OxT1, OxT2, HPT2. If above 30C aknowledge high temperature. If above 35C enter HOLD;;1;;;;00:10;
+130:40;EGSE/ MRL;Check Water Temperatures @ OxWT1, OxWT2, HPWT2;;1;;;;00:10;
 130:40;EGSE;Confirm storage capacity of CRio is greater than [!!!];;1;;;;00:10;
 68:40;MCC;BEGIN SEQUENCE Ox Fueling (PHASE RED);Ox Fueling (PHASE RED);3;;;;;
 68:50;WIND;Report on weather situation;;1;;;;;
 68:40;MCC;Announce end of Radio Silence;;3;;;;;
 68:40;EGSE;Turn OFF EPS_BAT;;3;;;;;
-126:50;OBDH/TMTC;Check RF451-Link;;1;;;;00:20;
+126:50;OBDH/ TMTC;Check RF451-Link;;1;;;;00:20;
 126:30;TMTC;Confirm GPS-lock;;1;;;;00:20;
 126:10;TMTC;Confirm Telemega-Link;;1;;;;00:20;
 125:50;OBDH;Test Connection to STX3;;1;;;;00:20;
@@ -276,9 +276,9 @@ vers.;v4.10;Launch Procedure;;0;MRL;MCC;RdHill;Time per step;
 67:40;EGSE;Open & Close HPV1 STEPWISE to more than 50 Bar @ RHPPT and confirm ROxTPT 50 Bar;;3;;;;;
 67:40;EGSE;Confirm HPV1 is closed;;3;;;;;
 67:40;OBDH;Open RDV SHORTLY, to check tightness @ RHPPT & ROxTPT (If leakages occur continue with Abort Procedure);;3;;;;;
-67:40;EGSE;Open MPV1/MPV2;;3;;;;;
+67:40;EGSE;Open MPV1/2;;3;;;;;
 67:40;EGSE;Open & Close MPV3 STEPWISE to 50 Bar @ OxOutPT;;3;;;;;
-67:40;EGSE;Close MPV1/MPV2;;3;;;;;
+67:40;EGSE;Close MPV1/2;;3;;;;;
 67:40;EGSE;Check & compare OxOutPT with OxInPT1;;3;;;;;
 67:40;EGSE;Check if RHPPT & ROxTPT more than OxInPT1, If less Open & Close HPV1;;3;;;;;
 67:40;EGSE;Zero OxTank Mass;;3;;;;;
@@ -306,7 +306,7 @@ vers.;v4.10;Launch Procedure;;0;MRL;MCC;RdHill;Time per step;
 9:50;EGSE;Decouple N2O coupling;;3;;;;00:20;
 9:30;MCC;Confirm End of Oxidator Fueling to OPS;;3;;;;00:15;
 9:20;WIND;Start wind weighting analysis;;1;;;;;
-9:15;OBDH/TMTC;Check RF451-Link;;3;;;;00:20;
+9:15;OBDH/ TMTC;Check RF451-Link;;3;;;;00:20;
 8:55;TMTC;Check GPS-lock;;3;;;;00:20;
 8:35;TMTC;Check Telemega-Link;;3;;;;00:20;
 33:40;EGSE;Verify He Bottle 2 Temperature @HPT2 & @HPWT2 (turn ON/OFF He_Heater if necessary) ;;1;;;;00:10;
@@ -324,7 +324,7 @@ vers.;v4.10;Launch Procedure;;0;MRL;MCC;RdHill;Time per step;
 8:15;EGSE;Turn OFF EPS_Ext (Switch to internal Power);;3;;;;00:20;
 7:55;OBDH;Confirm EPS Voltages are within limits;;3;;;;00:10;
 7:45;OBDH;Confirm RF451 Transmitting;;3;;;;00:05;
-7:40;OBDH/TMTC;Confirm RF451-Link;;3;;;;00:20;
+7:40;OBDH/ TMTC;Confirm RF451-Link;;3;;;;00:20;
 7:20;TMTC;Confirm GPS-lock;;3;;;;00:20;
 7:00;TMTC;Confirm Telemega-Link;;3;;;;00:20;
 6:40;OBDH;Switch to PREARMED;;3;;;;00:10;
@@ -337,7 +337,7 @@ vers.;v4.10;Launch Procedure;;0;MRL;MCC;RdHill;Time per step;
 6:05;EGSE;Open & Close HPV2 STEPWISE until RHPPT 300 Bar ;;3;;;;;
 6:05;EGSE;Open & close HPDV STEPWISE until HPLPT 0 Bar ;;3;;;;;
 6:05;EGSE;Confirm HPDV closed;;3;;;;;
-6:05;OBDH/EGSE;Check for leakage & HPLPT 0 Bar & RHPPT 300 Bar ;;3;;;;02:00;
+6:05;OBDH/ EGSE;Check for leakage & HPLPT 0 Bar & RHPPT 300 Bar ;;3;;;;02:00;
 6:05;EGSE;Turn OFF He_Heater;;3;;;;;
 4:05;OBDH;Acknowledge end of Fueling;;3;;;;00:10;
 3:55;MCC;Confirm End of Fueling to OPS;;3;;;;00:20;
@@ -401,7 +401,7 @@ vers.;v4.10;Launch Procedure;;0;MRL;MCC;RdHill;Time per step;
 0:00;EGSE;Close HPDV;;2;;;;;
 0:00;EGSE;Pressure Check;;2;;;;;
 0:00;MRL;Open MBV;;2;;;;;
-0:00;EGSE/MRL;Check and compare pressure HPPT1 with HPPG1;;2;;;;;
+0:00;EGSE/ MRL;Check and compare pressure HPPT1 with HPPG1;;2;;;;;
 0:00;MRL;Close MBV;;2;;;;;
 0:00;MRL;Take out B1 & B2 Bridges;;2;;;;;
 0:00;MRL;Safety is ensured;;2;;;;;