From d971473e07f7069b70d7449162709ffa7346487d Mon Sep 17 00:00:00 2001 From: Finn Hansch Date: Wed, 3 Jun 2020 16:00:21 +0200 Subject: [PATCH] changes from testrun 03.juni 2020 --- LaunchProcedure.csv | 92 ++++++++++++++++++++++----------------------- 1 file changed, 46 insertions(+), 46 deletions(-) diff --git a/LaunchProcedure.csv b/LaunchProcedure.csv index e12165b..d9c97c5 100644 --- a/LaunchProcedure.csv +++ b/LaunchProcedure.csv @@ -1,4 +1,4 @@ -vers.;v4.13;Launch Procedure;;0;MRL;MCC;RdHill;Time per step; +vers.;v4.14;Launch Procedure;;0;MRL;MCC;RdHill;Time per step; 147:20;WIND;Start wind weighting analysis;;1;;;;; 147:20;MCC;BEGIN SEQUENCE: Power on EGSE;Power on EGSE;1;;;;; 147:20;EGSE;Check CLD connection;;1;;;;; @@ -13,7 +13,7 @@ vers.;v4.13;Launch Procedure;;0;MRL;MCC;RdHill;Time per step; 146:20;EGSE @MRL;Switch ON Sup_24V_40A;;1;;;;; 146:20;EGSE @MRL;Switch ON Sup_5V_10A;;1;;;;03:00; 143:20;EGSE;Connect to cRio;;1;;;;; -130:40;EGSE;Confirm storage capacity of cRio is greater than [!!!];;1;;;;00:10; +130:40;EGSE;Confirm storage capacity of cRio is greater than 300MB;;;;00:10; 143:20;EGSE;Start RT_VI;;1;;;;; 143:20;EGSE;Open PID-VI and confirm it is running;;1;;;;; 143:20;EGSE;Rename PID-Logfile;;1;;;;02:00; @@ -49,7 +49,7 @@ vers.;v4.13;Launch Procedure;;0;MRL;MCC;RdHill;Time per step; 138:50;MRL;Couple Helium coupling;;1;;;;; 138:50;MRL;Couple N2O coupling;;1;;;;; 138:50;MRL;Reattach Pneumatic Line to Fueling arm;;1;;;;03:00; -135:50;EGSE;BEGIN SEQUENCE: EGSE Valve and Actuator check;EGSE Valve & Actuator Check;1;;;;; +135:50;EGSE;BEGIN SEQUENCE: EGSE sensor and actuator test;EGSE sensor & actuator test;1;;;;; 135:50;MCC;Confirm that video recording is enabled @ MCC;;1;;;;00:10; 135:50;MRL;Confirm that Ignition Umbilical is disconnected;;1;;;;; 135:40;OBDH;Check EPS hardware Voltages;;1;;;;00:10; @@ -68,22 +68,22 @@ vers.;v4.13;Launch Procedure;;0;MRL;MCC;RdHill;Time per step; 130:50;EGSE/ MRL;Check Bottle Temperatures @ OxT1, OxT2, HPT2. If above 30C aknowledge high temperature. If above 35C enter HOLD;;1;;;;00:10; 130:40;EGSE/ MRL;Check Water Temperatures @ OxWT1, OxWT2, HPWT2;;1;;;;00:10; 130:30;EGSE;Deactivate Heizi;;1;;;;00:10; -130:20;EGSE;Check OxV1 (CLD & RT_VI);;1;;;;00:10; -130:10;EGSE;Check OxV2 (CLD & RT_VI);;1;;;;00:10; -130:00;EGSE;Check MPV3 (CLD & RT_VI);;1;;;;00:10; -129:50;EGSE;Check HPV1 (CLD & RT_VI);;1;;;;00:10; -129:40;EGSE;Check HPV2 (CLD & RT_VI);;1;;;;00:10; -129:30;EGSE;Check MPV1/2 (CLD & RT_VI);;1;;;;00:10; -129:20;EGSE;Check RDV (CLD & RT_VI);;1;;;;00:10; -129:10;EGSE;Check RMOxOV (CLD & RT_VI);;1;;;;00:10; -129:00;EGSE;Check RMOxSV (CLD & RT_VI);;1;;;;00:10; +130:20;EGSE/ MRL;Check OxV1 (CLD & RT_VI);;1;;;;00:10; +130:10;EGSE/ MRL;Check OxV2 (CLD & RT_VI);;1;;;;00:10; +130:00;EGSE/ MRL;Check MPV3 (CLD & RT_VI);;1;;;;00:10; +129:50;EGSE/ MRL;Check HPV1 (CLD & RT_VI);;1;;;;00:10; +129:40;EGSE/ MRL;Check HPV2 (CLD & RT_VI);;1;;;;00:10; +129:30;EGSE/ MRL;Check MPV1/2 (CLD & RT_VI);;1;;;;00:10; +129:20;EGSE/ MRL;Check RDV (CLD & RT_VI);;1;;;;00:10; +129:10;EGSE/ MRL;Check RMOxOV (CLD & RT_VI);;1;;;;00:10; +129:00;EGSE/ MRL;Check RMOxSV (CLD & RT_VI);;1;;;;00:10; 128:50;OBDH;Activate Heizi;;1;;;;00:10; 128:40;OBDH;Verify Heizi @ RDVT & RDVET;;1;;;;01:00; -127:40;OBDH;Check RDV;;1;;;;00:10; -127:30;OBDH;Check RNCEV;;1;;;;00:10; -127:20;OBDH;Check RMOxOV;;1;;;;00:10; -127:10;OBDH;Check RMOxSV;;1;;;;00:10; -127:00;OBDH;Confirm RNCEV is disabled;;1;;;;00:10; +127:40;OBDH/ MRL;Check RDV;;1;;;;00:10; +127:30;OBDH/ MRL;Check RNCEV;;1;;;;00:10; +127:20;OBDH/ MRL;Check RMOxOV;;1;;;;00:10; +127:10;OBDH/ MRL;Check RMOxSV;;1;;;;00:10; +127:00;OBDH/ MRL;Disable RNCEV;;1;;;;00:10; 125:00;MRL;Confirm MBV closed;;1;;;;; 125:00;EGSE;Confirm that all valve switches are in OFF position (Except OxDV & HPDV);;1;;;;0:10; 115:00;MRL/ EGSE;Check loadcell by applying force to it;;1;;;;00:20; @@ -118,19 +118,19 @@ vers.;v4.13;Launch Procedure;;0;MRL;MCC;RdHill;Time per step; 130:50;EGSE/ MRL;Check Bottle Temperatures @ OxT1, OxT2, HPT2. If above 30C aknowledge high temperature. If above 35C enter HOLD;;1;;;;00:10; 130:40;EGSE/ MRL;Check Water Temperatures @ OxWT1, OxWT2, HPWT2;;1;;;;00:10; 110:00;MRL;Confirm that all hatches are closed;;1;;;;01:00; -109:00;MRL;Check He bottle 1 connector is attached;;1;;;;; -109:00;MRL;Check He bottle 2 connector is attached;;1;;;;; -109:00;MRL;Check N2O bottle 1 connector is attached;;1;;;;; -109:00;MRL;Check N2O bottle 2 connector is attached;;1;;;;; -109:00;MRL;Check hose between HPSM & N2OSM is connected on both ends;;1;;;;; -109:00;MRL;Check hose between HPSM & Flight Segment is connected on both ends;;1;;;;; -109:00;MRL;Check hose between N2OSM & Flight Segment is connected on both ends;;1;;;;; -109:00;MRL;Check pneumatic hose is connected on both ends;;1;;;;02:00; +109:00;MRL;Confirm He bottle 1 connector is attached;;1;;;;; +109:00;MRL;Confirm He bottle 2 connector is attached;;1;;;;; +109:00;MRL;Confirm N2O bottle 1 connector is attached;;1;;;;; +109:00;MRL;Confirm N2O bottle 2 connector is attached;;1;;;;; +109:00;MRL;Confirm hose between HPSM & N2OSM is connected on both ends;;1;;;;; +109:00;MRL;Confirm hose between HPSM & Flight Segment is connected on both ends;;1;;;;; +109:00;MRL;Confirm hose between N2OSM & Flight Segment is connected on both ends;;1;;;;; +109:00;MRL;Confirm pneumatic hose is connected on both ends;;1;;;;02:00; 107:00;MRL;Put on safety equipment;;2;;;;; 107:00;MRL;Confirm MBV is closed;;2;;;;; 107:00;MRL;Confirm HPNV1 is closed;;2;;;;; 107:00;MRL;Confirm HPNV2 is closed;;2;;;;; -107:00;MRL;Take position to open He Bottle 1;;2;;;;; +107:00;MRL;Take positions to open He Bottle 1;;2;;;;; 107:00;EGSE;Confirm HPV1 is closed;;2;;;;; 107:00;EGSE;Confirm MPV1/2 is closed;;2;;;;; 107:00;MRL;Open He Bottle 1;;2;;;;01:00; @@ -142,14 +142,13 @@ vers.;v4.13;Launch Procedure;;0;MRL;MCC;RdHill;Time per step; 105:00;EGSE/ MRL;Open & Close HPV1 SHORTLY & Check HPPT1;;2;;;;; 105:00;EGSE;Check HPPT1 300 Bar;;2;;;;; 105:00;EGSE;Confirm HPLPT 0 Bar;;2;;;;; -105:00;EGSE/ MRL;Open & Close HPV2 SHORTLY & Check HPPT2 0 bar;;2;;;;; -105:00;EGSE/ MRL;Open & Close HPDV SHORTLY & Check HPLPT 0 bar;;2;;;;; +105:00;EGSE/ MRL;Open & Close HPV2 SHORTLY & Confirm HPPT2 0 bar;;2;;;;; +105:00;EGSE/ MRL;Open & Close HPDV SHORTLY & Confirm HPLPT 0 bar;;2;;;;; 105:00;EGSE/ MRL;Open & Close OxV1 SHORTLY;;2;;;;; 105:00;EGSE/ MRL;Open & Close OxV2 SHORTLY;;2;;;;; 105:00;EGSE/ MRL;Open & Close OxDV SHORTLY;;2;;;;; 105:00;EGSE/ MRL;Open & Close MPV3 SHORTLY;;2;;;;; 00:00;MRL;Open HPNV1;;2;;;;;; -10:10;MRL;????!!!!DO NOT EXECUTE BEFORE DISCUSSION!!!!!Open HPNV2 1/8 Rev;;2;;;;; 00:00;MRL;Step Back;;2;;;;;; 00:00;EGSE;Open & Close HPV1 STEPWISE untile HPLPT equal to HPPT1 and check for leakage @HPLPT (If leakage occurs continue with "GSE Passivation Procedure");;2;;;;; 00:00;EGSE;Confirm RHPPT & RoxTPT less than 1 Bar (on Pressure continue with "Rocket Passivation Procedure");;2;;;;; @@ -170,7 +169,7 @@ vers.;v4.13;Launch Procedure;;0;MRL;MCC;RdHill;Time per step; 87:10;EGSE;Open & Close STEPWISE OxV2 to 0 Bar @OxInPT2;;2;;;;; 87:10;EGSE;Confirm OxOutPT 0 Bar;;2;;;;; 87:10;EGSE;Close OxDV;;2;;;;; -105:00;EGSE;Check HPLPT & OxOutPT 0 Bar;;2;;;;01:30; +105:00;EGSE;Confirm HPLPT & OxOutPT 0 Bar;;2;;;;01:30; 103:30;EGSE;Decouple N2O coupling;;2;;;;; 103:30;EGSE;Decouple Helium coupling;;2;;;;00:20; 103:10;EGSE;Move arm away from rocket;;2;;;;; @@ -189,7 +188,7 @@ vers.;v4.13;Launch Procedure;;0;MRL;MCC;RdHill;Time per step; 100:40;MRL;Confirm PPG 0 Bar;;1;;;;00:20; 100:40;MRL;Release Pneumatic lines of couplings;;1;;;;00:20; 100:20;EGSE;Confirm Fueling arm is switched OFF;;1;;;;; -100:20;EGSE;Check OxOutPT and HPLPT 0 bar;;1;;;;; +100:20;EGSE;Confirm OxOutPT and HPLPT 0 bar;;1;;;;; 100:20;MRL;Couple He coupling;;1;;;;00:30; 99:50;MRL;Couple N2O coupling;;1;;;;00:30; 99:50;MRL;Confirm He coupling is connected properly;;1;;;;; @@ -210,15 +209,15 @@ vers.;v4.13;Launch Procedure;;0;MRL;MCC;RdHill;Time per step; 95:30;MRL;Confirm Bridge Hatch is Secured;;1;;;;00:20; 95:10;EGSE @MRL;return to MCC;;1;;;;; 95:10;OPS;Elevate MRL to 90 degrees;;1;;;;05:00; -89:40;EGSE;Calibrate loadcell (Set to 0);;1;;;;01:00; +89:40;EGSE;Zero OxTank Mass;;1;;;;01:00; 88:40;MCC;BEGIN SEQUENCE: Fueling Preparations (PHASE YELLOW);Fueling Preparations;2;;;;; 130:50;EGSE/ MRL;Check Bottle Temperatures @ OxT1, OxT2, HPT2. If above 30C aknowledge high temperature. If above 35C enter HOLD;;1;;;;00:10; 130:40;EGSE/ MRL;Check Water Temperatures @ OxWT1, OxWT2, HPWT2;;1;;;;00:10; -127:40;OBDH;Check RDV;;1;;;;00:10; -127:30;OBDH;Check RNCEV;;1;;;;00:10; -127:20;OBDH;Check RMOxOV;;1;;;;00:10; -127:10;OBDH;Check RMOxSV;;1;;;;00:10; -127:00;OBDH;Confirm RNCEV is disabled;;1;;;;00:10; +127:40;OBDH;!!!Check RDV;;1;;;;00:10; +127:30;OBDH;!!!Check RNCEV;;1;;;;00:10; +127:20;OBDH;!!!Check RMOxOV;;1;;;;00:10; +127:10;OBDH;!!!Check RMOxSV;;1;;;;00:10; +127:00;OBDH;!!!Disable RNCEV;;1;;;;00:10; 88:40;MRL;Put on safety equipment;;2;;;;00:30; 10:10;MRL;Confirm HPNV1 is Open;;2;;;;; 10:10;MRL;Confirm HPNV2 is Closed;;2;;;;; @@ -258,16 +257,17 @@ vers.;v4.13;Launch Procedure;;0;MRL;MCC;RdHill;Time per step; 68:40;MCC;CONTINUE AFTER HOLD;2;;;;;; 130:50;EGSE/ MRL;Check Bottle Temperatures @ OxT1, OxT2, HPT2. If above 30C aknowledge high temperature. If above 35C enter HOLD;;1;;;;00:10; 130:40;EGSE/ MRL;Check Water Temperatures @ OxWT1, OxWT2, HPWT2;;1;;;;00:10; -130:40;EGSE;Confirm storage capacity of CRio is greater than [!!!];;1;;;;00:10; +130:40;EGSE;Confirm storage capacity of CRio is greater than 300MB;;1;;;;00:10; +127:00;OBDH;Confirm RNCEV is disabled;;1;;;;00:10; 68:40;MCC;BEGIN SEQUENCE Ox Fueling (PHASE RED);Ox Fueling (PHASE RED);3;;;;; 68:50;WIND;Report on weather situation;;1;;;;; 68:40;MCC;Announce end of Radio Silence;;3;;;;; 68:40;EGSE;Turn OFF EPS_BAT;;3;;;;; -126:50;OBDH/ TMTC;Check RF451-Link;;1;;;;00:20; +126:50;OBDH/ TMTC;Confirm RF451-Link;;1;;;;00:20; 126:30;TMTC;Confirm GPS-lock;;1;;;;00:20; 126:10;TMTC;Confirm Telemega-Link;;1;;;;00:20; 125:50;OBDH;Test Connection to STX3;;1;;;;00:20; -125:30;OBDH;Confirm that STX3 Package received by email;;1;;;;00:30; +125:30;OBDH;Confirm that STX3 Packages are received by email;;1;;;;00:30; 125:30;AVC;Turn on main TMTC screen;;1;;;;00:30; 125:30;MCC;Request Permission to begin fueling from OPS;;1;;;;03:00; 68:40;OBDH;Acknowledge start of Fueling;;3;;;;01:00; @@ -302,7 +302,7 @@ vers.;v4.13;Launch Procedure;;0;MRL;MCC;RdHill;Time per step; 33:40;EGSE;Verify He Bottle 2 Temperature @HPT2 & @HPWT2 (turn ON He_Heater if necessary) ;;1;;;;00:10; 10:20;MCC;Provide OxTankMass and temperature readings to Wind weighting station;;3;;;;00:30; 9:50;EGSE;Confirm OxV1 & OxV2 closed;;3;;;;; -9:50;EGSE;Check OxOutPT 0 Bar;;3;;;;; +9:50;EGSE;Confirm OxOutPT 0 Bar;;3;;;;; 9:50;EGSE;Decouple N2O coupling;;3;;;;00:20; 9:30;MCC;Confirm End of Oxidator Fueling to OPS;;3;;;;00:15; 9:20;WIND;Start wind weighting analysis;;1;;;;; @@ -343,7 +343,7 @@ vers.;v4.13;Launch Procedure;;0;MRL;MCC;RdHill;Time per step; 3:55;MCC;Confirm End of Fueling to OPS;;3;;;;00:20; 3:35;MCC;BEGIN SEQUENCE: Disconnecting Fueling Arm;Disconnecting Fueling Arm;3;;;;00:10; 3:25;EGSE;Confirm HPV1 & HPV2 closed;;3;;;;00:10; -3:15;EGSE;Check HPLPT 0 Bar ;;3;;;;00:10; +3:15;EGSE;Confirm HPLPT 0 Bar ;;3;;;;00:10; 3:05;EGSE;Decouple Helium coupling;;3;;;;00:20; 2:45;EGSE;Confirm Helium coupling is disconnected;;3;;;;00:10; 2:35;EGSE;Move fueling arm away from rocket;;3;;;;00:40; @@ -373,10 +373,10 @@ vers.;v4.13;Launch Procedure;;0;MRL;MCC;RdHill;Time per step; 0:00;MRL;RETURN to Block House;;2;;;;; 0:00;EGSE;Open OxDV;;2;;;;; 0:00;EGSE;Open OxV1;;2;;;;; -0:00;EGSE;Check OxInPT1 & OxOutPT 0 Bar;;2;;;;; +0:00;EGSE;Confirm OxInPT1 & OxOutPT 0 Bar;;2;;;;; 0:00;EGSE;Close OxV1;;2;;;;; 0:00;EGSE;Open OxV2;;2;;;;; -0:00;EGSE;Check OxInPT2 & OxOutPT 0 Bar;;2;;;;; +0:00;EGSE;Confirm OxInPT2 & OxOutPT 0 Bar;;2;;;;; 0:00;EGSE;Close OxV2;;2;;;;; 0:00;EGSE;Close OxDV ;;2;;;;; 0:00;MRL;Go to MRL, confirm OxInPG1 & OxInPG2 0 Bar, else RETURN to Block House, THEN... @@ -385,7 +385,7 @@ vers.;v4.13;Launch Procedure;;0;MRL;MCC;RdHill;Time per step; 0:00;MRL;Return to Block House;;2;;;;; 0:00;EGSE;Open HPDV;;2;;;;; 0:00;EGSE;Open HPV2;;2;;;;; -0:00;EGSE;Check pressure HPLPT & HPPT2 0 Bar;;2;;;;; +0:00;EGSE;Confirm pressure HPLPT & HPPT2 0 Bar;;2;;;;; 0:00;EGSE;Close HPV2;;2;;;;; 0:00;EGSE;Close HPDV;;2;;;;; 0:00;MRL;Go to Testrig, confirm HPPG2 0 Bar, else return to Block House, THEN...;;2;;;;; @@ -396,7 +396,7 @@ vers.;v4.13;Launch Procedure;;0;MRL;MCC;RdHill;Time per step; 0:00;MRL;Step back;;2;;;;; 0:00;EGSE;Open HPDV;;2;;;;; 0:00;EGSE;Open HPV1;;2;;;;; -0:00;EGSE;Check pressure HPLPT & HPPT1 0 Bar;;2;;;;; +0:00;EGSE;Confirm pressure HPLPT & HPPT1 0 Bar;;2;;;;; 0:00;EGSE;Close HPV1;;2;;;;; 0:00;EGSE;Close HPDV;;2;;;;; 0:00;EGSE;Pressure Check;;2;;;;;