procedure/LaunchProcedure.csv

1	vers.	v4.3	Launch Procedure		0	MRL	MCC	RdHill	Time per step
2	147:20	MCC	BEGIN SEQUENCE: Power on EGSE	Power on EGSE	1
3	147:20	EGSE	Check CLD connection		1
4	147:20	EGSE	Switch ON CLD via Battery & check voltage (24 Volt)		1
5	147:20	EGSE	Switch ON the primary and secondary supply switches on the Control Panel		1				01:00
6	146:20	EGSE@MRL	Switch ON Sup_24V_20A & check voltage (ca. 27,2 Volt)		1
7	146:20	EGSE@MRL	Switch ON Sup_24V_10A & check voltage (ca. 27,2 Volt)		1
8	146:20	EGSE@MRL	Switch ON Sup_12V_10A & check voltage (ca. 13,8 Volt)		1
9	146:20	EGSE@MRL	Switch ON Bat_24V_20A & check voltage (ca. 27,9 Volt)		1
10	146:20	EGSE@MRL	Switch ON Bat_24V_10A & check voltage (ca. 27,9 Volt)		1
11	146:20	EGSE@MRL	Switch ON Bat_12V_10A & check voltage (ca. 13,8 Volt)		1
12	146:20	EGSE@MRL	Switch ON Sup_24V_40A		1
13	146:20	EGSE@MRL	Switch ON Sup_5V_10A		1				03:00
14	143:20	EGSE	Connect to cRIO		1
15	143:20	EGSE	Start FPGA_VI		1
16	143:20	EGSE	Start RT_VI		1
17	143:20	EGSE	Confirm PID-VI is running		1
18	143:20	EGSE	Rename PID-Logfile		1				02:00
19	141:20	MRL	Confirm working Personel is grounded		1
20	141:20	EGSL@MRL	Confirm all 8 Groundingbridges are inserted		1
21	141:20	MCC	BEGIN SEQUENCE: Connect Data Umbilical	Connect Data Umbilical	1				00:30
22	140:50	EGSE	Turn on EPS_BAT		1
23	140:50	EGSE	Turn on EPS_EXT		1
24	140:50	EGSE@MRL	Remove 7 Grounding Bridges and leave EPS_BAT inserted		1
25	140:50	EGSE@MRL	Insert EPS_EXT Fuse in Power Supply Control Panel		1
26	140:50	EGSE@MRL	Confirm green LED at EPS_EXT Fuse is on		1
27	140:50	EGSE@MRL	Insert Main_Bus Fuse in Power Supply Control Panel		1
28	140:50	EGSE@MRL	Confirm LED at Main_Bus Fuse is OFF. Else Pull fuse and insert all Grounding Bridges		1
29	140:50	EGSE@MRL	Set remaining Fuses (except Payload Fuse) and check for green LED		1
30	140:50	EGSE	Turn OFF EPS_BAT		1
31	140:50	EGSE@MRL	Confirm Main bus LED is on.		1
32	140:50	EGSE	Start EPS via EPS_ext		1
33	140:50	OBDH	Clear SD-Card-using FileZilla FTP		1				01:00
34	139:50	OBDH	Connect to sbRIO		1
35	139:50	OBDH	Start RT_Main		1
36	139:50	MRL	Confirm 3 beeps at OBC1		1
37	139:50	OBDH	Open RT_Sub_HMI		1
38	139:50	OBDH	Confirm Main Chute button is disabled		1
39	139:50	EGSE@MRL	Insert Payload Fuse		1
40	139:50	EGSE@MRL	Confirm green LED at Payload Fuse is on		1
41	139:50	MCC	BEGIN SEQUENCE: Connect Fueling arm	Connect Fueling Arm	1
42	139:50	MRL	Confirm working Personel is grounded		1				01:00
43	138:50	MRL	Remove Pneumatic Line from Fueling arm		1
44	138:50	MRL	Move Fueling arm to rocket		1
45	138:50	MRL	Couple Helium coupling		1
46	138:50	MRL	Couple N2O coupling		1
47	138:50	MRL	Reattach Pneumatic Line to Fueling arm		1				03:00
48	135:50	EGSE	BEGIN SEQUENCE: EGSE Valve and Actuator check	EGSE Valve & Actuator Check	1
49	135:50	MCC	Confirm that video recording is enabled @ MCC		1				00:10
50	135:50	MRL	Confirm that Ignition Umbilical is disconnected		1
51	135:40	OBDH	Check EPS hardware Voltages		1				00:10
52	135:30	EGSE	Start PID data recording		1				00:10
53	135:20	MRL	Close HPNV		1				00:10
54	135:10	EGSE/MRL	Switch OxDV to closed & check if magnetic valve LED is on		1				00:10
55	135:00	EGSE/MRL	Switch HPDV to closed & check if magnetic valve LED is on		1				00:10
56	134:50	EGSE/MRL	Check warning lamp on HPSM		1				00:10
57	134:40	MRL	Remove loose equipment		1				03:00
58	131:40	EGSE	Activate Heizi		1				00:10
59	131:30	EGSE	Activate N2O_Heater 1		1				00:10
60	131:20	EGSE	Activate N2O_Heater 2		1				00:10
61	131:10	EGSE	Activate He_Heater		1				00:10
62	131:00	OBDH	Verify Heizi @ RDVT & RDVET		1				00:10
63	130:50	EGSE/MRL	Verify Bottle Temperatures @ OxT1, OxT2, HPT2		1				00:10
64	130:40	EGSE/MRL	Verify Water Temperatures @ Ox@T1, OxWT2, HPWT2		1				00:10
65	130:30	EGSE	Deactivate Heizi		1				00:10
66	130:20	EGSE	Check OxV1 (CLD & RT_VI)		1				00:10
67	130:10	EGSE	Check OxV2 (CLD & RT_VI)		1				00:10
68	130:00	EGSE	Check MPV3 (CLD & RT_VI)		1				00:10
69	129:50	EGSE	Check HPV1 (CLD & RT_VI)		1				00:10
70	129:40	EGSE	Check HPV2 (CLD & RT_VI)		1				00:10
71	129:30	EGSE	Check MPV1/2 (CLD & RT_VI)		1				00:10
72	129:20	EGSE	Check RDV (CLD & RT_VI)		1				00:10
73	129:10	EGSE	Check RMOxOV (CLD & RT_VI)		1				00:10
74	129:00	EGSE	Check RMOxSV (CLD & RT_VI)		1				00:10
75	128:50	OBDH	Activate Heizi		1				00:10
76	128:40	OBDH	Verify Heizi @ RDVT & RDVET		1				01:00
77	127:40	OBDH	Check RDV		1				00:10
78	127:30	OBDH	Check RNCEV		1				00:10
79	127:20	OBDH	Check RMOxOV		1				00:10
80	127:10	OBDH	Check RMOxSV		1				00:10
81	127:00	OBDH	Confirm RNCEV is disabled		1				00:10
82	125:00	MRL	Confirm MBV closed		1
83	125:00	EGSE	Confirm that all valve switches are in OFF position (Except OxDV & HPDV)		1				10:00
84	115:00	MRL/EGSE	Check loadcell by applying force to it		1				00:20
85	114:40	OBDH	Check RHPPT shows atmosphere		1
86	114:40	OBDH	Check ROxTPT shows atmosphere		1
87	114:40	OBDH	Check RIHPT shows atmosphere		1
88	114:40	OBDH	Check RCCPT shows atmosphere		1
89	114:40	OBDH	Check RBaro1 shows atmosphere		1
90	114:40	OBDH	Check RBaro2 shows atmosphere		1
91	114:40	EGSE	Check HPPT1 shows 0 bar		1				00:20
92	114:20	EGSE	Check HPPT2 shows 0 bar		1
93	114:20	EGSE	Check HPLPT shows 0 bar		1
94	114:20	EGSE	Check OxInPT1 shows 0 bar		1
95	114:20	EGSE	Check OxInPT2 shows 0 bar		1
96	114:20	EGSE	Check OxOutPT shows 0 bar		1				00:20
97	114:00	EGSE/MRL	Switch on N2O coupling & check if magnetic valve LED is on		1
98	114:00	EGSE/MRL	Switch on He coupling & check if magnetic valve LED is on		1
99	114:00	EGSE/MRL	Switch on swivle arm & check if magnetic valve LED is on		1
100	114:00	EGSE	Switch off swivel arm & He coupling & N2O coupling		1				01:00
101	114:00	MCC	BEGIN SEQUENCE: Ignition signal Test	Ignition signal Test	1				01:00
102	113:00	MRL	Confirm that Ignition Umbilical is disconnected		1
103	113:00	MRL	Connect Ignition test receptical		1
104	113:00	EGSE@MRL	Plug in Bridges B1 and B2		1
105	113:00	MRL	Confirm Soundsignal from Ignition Umbilical		1
106	113:00	EGSE	Turn on Ignition Secure Switch		1
107	113:00	EGSE/OBDH	Turn on Ignition Switch for 2 Second & Confirm ignition signal received at sbRio		1
108	113:00	EGSE/OBDH	Confirm that Ignition Switch is switched off		1
109	113:00	EGSE	Turn off Ignition Secure Switch		1
110	113:00	EGSE@MRL	Remove Bridges B1 and B2		1
111	113:00	MRL	Remove Ignition test receptical		1				03:00
112	110:00	MCC	BEGIN SEQUENCE: pneumatic pressure test (PHASE YELLOW)	Pneumatic Pressure Test	1
113	110:00	MRL	Confirm that all hatches are closed		1				01:00
114	109:00	MRL	Check He bottle 1 connector is attached		1
115	109:00	MRL	Check He bottle 2 connector is attached		1
116	109:00	MRL	Check N2O bottle 1 connector is attached		1
117	109:00	MRL	Check N2O bottle 2 connector is attached		1
118	109:00	MRL	Check hose between HPSM & N2OSM is connected on both ends		1
119	109:00	MRL	Check hose between HPSM & Flight Segment is connected on both ends		1
120	109:00	MRL	Check hose between N2OSM & Flight Segment is connected on both ends		1
121	109:00	MRL	Check Pneumatik hose is connected on both ends		1				02:00
122	107:00	MRL	Put on safety equipment		2
123	107:00	MRL	Move into Position to open He Bottle 1		2
124	107:00	MRL	Confirm MBV is closed		2
125	107:00	EGSE	Confirm if HPV1 is closed		2
126	107:00	EGSE	Confirm MPV1/2 is closed		2
127	107:00	MRL	Open He Bottle 1		2				01:00
128	106:00	MRL	Check & compare pressure HPPT1 with HPPG1 (max 300 bar)		2
129	106:00	MRL	Check Gastech Silver HPPR1 (max 300 to 50 bar)		2
130	106:00	MRL	Check Harris PPR (50 to 8 bar)		2
131	106:00	MRL	Check pneumatic PPG (8 bar)		2
132	106:00	MRL	Step back		2				01:00
133	105:00	EGSE/MRL	Open & Close HPV1 SHORTLY & Check HPPT1		2
134	105:00	EGSE	Confirm HPPT1 is at 300 Bar		2
135	105:00	EGSE	Confirm HPLPT less than 10 Bar		2
136	105:00	EGSE/MRL	Open & Close HPV2 SHORTLY & Check HPPT2 0 bar		2
137	105:00	EGSE/MRL	Open & Close HPDV SHORTLY & Check HPLPT 0 bar		2
138	105:00	EGSE/MRL	Open & Close OxV1 SHORTLY		2
139	105:00	EGSE/MRL	Open & Close OxV2 SHORTLY		2
140	105:00	EGSE/MRL	Open & Close OxDV SHORTLY		2
141	105:00	EGSE/MRL	Open & Close MPV3 SHORTLY		2
142	105:00	EGSE	Check HPLPT & OxOutPT 0 Bar		2				01:30
143	103:30	EGSE	Decouple N2O coupling		2
144	103:30	EGSE	Decouple Helium coupling		2				00:20
145	103:10	EGSE	Move arm away from rocket		2
146	103:10	EGSE	Move arm to rocket		2				01:00
147	102:10	MRL	Close He Bottle 1 and check HPSM for leakage (If leakage occurs Abort)		2				01:00
148	101:10	MRL	Open HPNV 1/8 Rev		2
149	101:10	MRL	Open MBV		2
150	101:10	EGSE/MRL	Check and compare pressure HPPT1 with HPPG1 0 Bar		2
151	101:10	MRL	Close MBV		2				00:30
152	100:40	MRL	Safety is ensured		2
153	100:40	MCC	MiS to MRL		1
154	100:40	EGSE	Switch off N20 coupling		1
155	100:40	EGSE	Switch off He coupling		1
156	100:40	MRL	Release Pneumatic lines of couplings		1				00:20
157	100:20	EGSE	Confirm Fueling arm is switched off		1
158	100:20	EGSE	Check OxOutPT and HPLPT 0 bar		1
159	100:20	MRL	Couple Helium coupling		1				00:30
160	99:50	MRL	Couple N2O coupling		1				00:30
161	99:20	MRL	HOLD	HOLD	1
162	99:20	MCC	CONTINUE AFTER HOLD
163	99:20	MRL	BEGIN SEQUENCE: Arming Rocket Part 1	Arming Rocket Pt.1	1
164	98:50	MRL	Turn on GoPro Camera at end of Launch Rail		1				00:20
165	99:20	MRL	Connect Ignition Umbilical		1				00:30
166	98:30	MRL	Insert all EPS Bridges		1				03:00
167	95:30	MRL	Confirm Bridge Hatch is Secured		1				00:20
168	95:10	EGSE@MRL	return to MCC		1
169	95:10	OPS	Elevate MRL to 90 degrees		1				05:00
170	90:10	EGSE	Powercycle EPS to to start flight mode on Telemega		1				00:30
171	89:40	EGSE	Calibrate loadcell (Set to 0)		1				01:00
172	88:40	MCC	BEGIN SEQUENCE: Fueling Preparations (PHASE YELLOW)	Fueling Preparations	2
173	88:40	MRL	Put on safety equipment		2				00:30
174	88:10	MRL	Open He Bottle 1		2				01:00
175	87:10	MRL	Step back		2
176	87:10	EGSE	Open & Close STEPWISE MPV1/MPV2 to 50 Bar @ OxInPT1 & OxInPT2		2
177	87:10	EGSE/MRL	Check & compare OxInPT1 with OxInPG1 based on Bottle temperature (max 50 bar)		2
178	87:10	EGSE/MRL	Check & compare pressure OxInPT2 with OxInPG2 based on Bottle temperature (max 50 bar)		2
179	87:10	EGSE/MRL	Check Temperature of N2O Bottle 1 @OxT1 & OxWT1 (max 22C)		2
180	87:10	EGSE/MRL	Check Temperature of N2O Bottle 2 @OxT2 & OxWT2 (max 22C)		2				01:30
181	85:40	MRL	Open He Bottle 2		2
182	85:40	EGSE/MRL	Check & compare pressure HPPT2 with HPPG2 (max 315 bar)		2				01:00
183	84:40	ALL/MRL	CAUTION!		2
184	84:40	MRL	Open N2O Bottle 1		2
185	84:40	MRL/EGSE	Check & compare pressure OxInPT 1 with OxInPG 1 (max 50 bar)		2				02:00
186	82:40	MRL	Open N2O Bottle 2		2
187	82:40	MRL/EGSE	Check & compare pressure OxInPT 2 with OxInPG 2 (max 50 bar)		2				02:00
188	80:40	MRL	Insert Ignition Bridges B1 and B2 into EGSE		2				02:00
189	78:40	MRL	Confirm Soundsignal from Ignition Umbilical		2
190	78:40	MRL	Close ComTerm		2
191	78:40	ALL	Clear Launchpad and inform OPS		2				10:00
192	68:40	KLP	Start Camera Karsten Lapp<70>hn		2
193	68:40	MCC	HOLD	HOLD	2
194	68:40	MCC	CONTINUE AFTER HOLD
195	68:40	MCC	BEGIN SEQUENCE Ox Fueling (PHASE RED)	Ox Fueling (PHASE RED)	3
196	68:40	MCC	Announce end of Radio Silence		3
197	126:50	OBDH/TMTC	Check RF451-Link		1				00:20
198	126:30	TMTC	Confirm GPS-lock		1				00:20
199	126:10	TMTC	Confirm Telemega-Link		1				00:20
200	125:50	OBDH	Test Connection to STX3		1				00:20
201	125:30	OBDH	Confirm that STX3 Package received by email		1				00:30
202	125:30	MCC	Request Permission to begin fueling from OPS		1				03:00
203	68:40	OBDH	Acknowledge start of Fueling		3				01:00
204	67:40	EGSE	Open & Close HPV1 STEPWISE to 50 Bar @ ROxTPT (stop at 30 bar and wait 30 seconds to check for leakage)		3
205	67:40	EGSE	Open & Close HPV1 STEPWISE to more than 50 Bar @ RHPPT and check ROxTPT 50 Bar		3
206	67:40	EGSE	Check if HPV1 is closed		3
207	67:40	OBDH	Open RDV SHORTLY, to check tightness @ RHPPT & ROxTPT (If leakages occur Abort)		3
208	67:40	EGSE	Open MPV1/MPV2		3
209	67:40	EGSE	Open & Close MPV3 STEPWISE to 50 Bar @ OxOutPT		3
210	67:40	EGSE	Close MPV1/MPV2		3
211	67:40	EGSE	Check & compare OxOutPT with OxInPT1		3
212	67:40	EGSE	Check if RHPPT & ROxTPT more than OxInPT1, If less Open & Close HPV1		3
213	67:40	EGSE	Zero OxTank Mass		3
214	67:40	MCC	Write down Time		3
215	67:40	EGSE	Open OxV1		3				04:00
216	63:40	OBDH	Open & Close RDV STEPWISE until N2O bottle empty or 25kg OxTankMass, keep temperatures RDVT and RDVET above 10<31>C and Check delta ROxTPT and OxInPT1		3				30:00:00
217	33:40	EGSE	Close OxV1		3				00:10
218	33:30	EGSE	Check if Pressure rises in OxPT1, if Pressure rises relief via OxV1 or wait for Pressure relief valve		3				01:00
219	32:30	EGSE	Check & compare OxOutPT with OxInPT2		3
220	32:30	EGSE	Check & compare RHPPT & ROxTPT 50 Bar and more than OxInPT2, If less Open & Close HPV1		3
221	32:30	EGSE	Open OxV2		3
222	32:30	OBDH	Open & Close RDV STEPWISE to 25kg OxTankMass, keep temperatures RDVT and RDVET above 10<31>C and Check delta OxTPT and OxInPT1		3				20:00
223	12:30	EGSE	Close OxV2		3				00:10
224	12:20	EGSE	Check if Pressure rises in OxPT2, if Pressure rises relief via OxV2 or wait for Pressure relief valve		3				01:00
225	11:20	EGSE	Open OxDV STEPWISE until OxOutPT 0 Bar		3
226	11:20	OBDH	Check ROxCV for tightness @ ROxTPT		3
227	11:20	EGSE	Close OxDV		3				01:00
228	10:20	EGSE	Write down OxTankMass		3
229	10:20	MCC	Provide OxTankMass and temperature readings to Wind weighting station		3				00:30
230	9:50	EGSE	Confirm OxV1 & OxV2 closed		3
231	9:50	EGSE	Check OxOutPT 0 Bar		3
232	9:50	EGSE	Decouple N2O coupling		3				00:20
233	9:30	MCC	Confirm End of Oxidator Fueling to OPS		3				00:15
234	9:15	OBDH/TMTC	Check RF451-Link		3				00:20
235	8:55	TMTC	Check GPS-lock		3				00:20
236	8:35	TMTC	Check Telemega-Link		3				00:20
237	8:15	MCC	HOLD	HOLD	3
238	8:15	OPS	Align MRL to Launch Trajectory		3
239	8:15	MCC	Turn audio volume down		3
240	8:15	MCC	Turn off Confirm delay		3
241	8:15	MCC	Confirm MRL adjustment with OPS		3
242	8:15	ALL	Talk through Launch Sequence		3
243	8:15	AVC	Start Video Recording in Block House		3
244	8:15	MCC	CONTINUE AFTER HOLD
245	8:15	MCC	BEGIN Switching to Internal Power Sequence	Switch to Internal Power	3
246	8:15	EGSE	Switch to internal Power		3				00:20
247	7:55	OBDH	Confirm EPS Voltages are within limits		3				00:10
248	7:45	OBDH	Confirm RF451 Transmitting		3				00:05
249	7:40	OBDH/TMTC	Confirm RF451-Link		3				00:20
250	7:20	TMTC	Confirm GPS-lock		3				00:20
251	7:00	TMTC	Confirm Telemega-Link		3				00:20
252	6:40	OBDH	Switch to PREAMRED		3				00:10
253	6:30	PYL	Confirm Payload is running		3				00:20
254	6:10	AVC	Confirm that videorecording @ MCC is running		3				00:05
255	6:05	MCC	BEGIN SEQUENCE: High Pressure Fueling	High Pressure Fueling	3
256	6:05	EGSE	Open & Close HPV1 STEPWISE until RHPPT 300 Bar or pressure equal to He Bottle 1		3
257	6:05	EGSE	Open & Close HPV2 STEPWISE until RHPPT 300 Bar		3
258	6:05	EGSE	Open & close HPDV STEPWISE until HPLPT 0 Bar		3
259	6:05	EGSE	Confirm HPDV closed		3
260	6:05	OBDH/EGSE	Check for leakage & HPLPT 0 Bar & RHPPT 300 Bar		3				02:00
261	4:05	OBDH	Acknowledge end of Fueling		3				00:10
262	3:55	MCC	Confirm End of Fueling to OPS		3				00:20
263	3:35	MCC	BEGIN SEQUENCE: Disconnecting Fueling Arm	Disconnecting Fueling Arm	3				00:10
264	3:25	EGSE	Confirm HPV1 & HPV2 closed		3				00:10
265	3:15	EGSE	Check HPLPT 0 Bar		3				00:10
266	3:05	EGSE	Decouple Helium coupling		3				00:20
267	2:45	EGSE	Confirm Helium coupling is disconnected		3				00:10
268	2:35	EGSE	Move fueling arm away from rocket		3				00:40
269	1:55	MCC	Confirm Fueling Arm away to OPS		3				00:15
270	1:40	MCC	Prepare for Launch		3				00:10
271	1:30	OBDH	Confirm ready for launch		3				00:10
272	1:20	EGSE	Confirm ready for launch		3				00:10
273	1:10	MCC	Set Go/No-Go System to Go		3				00:10
274	1:00	MCC	Wait for Authorization for Launch		3				00:00
275	1:00	MCC	BEGIN SEQUENCE: Ignition	Ignition Sequence	4				00:10
276	0:50	OBDH	ARM		4				00:05
277	0:45	OBDH	Confirm all status indicators green		4				00:05
278	0:40	OBDH	Disconnect Ethernet		4				00:30
279	0:10	EGSE	Turn on Ignition Secure		4				00:07
280	0:03	EGSE	T-3: Ignition		4				00:03
281	0:00	OBDH	T+0: Verify RMOxOV Open (Launched)		4				00:00
282	0:00	EGSE	T+1: Turn OFF Ignition		4
283	0:00	EGSE	T+5: Turn OFF Ignition Secure		4
284	0:00	OBDH	T+20: Verify RMOxOV Closed and RMOxSV Open (Cruise)		4
285	0:00	OBDH	T+50: Verify RNCEV Open (Drogue)		4
286	0:00	OBDH	T+310: Verify Main Chute Deployed and RDV Open (Main)		4
287	0:00	OBDH	T+600: Verify (Landed)		4
288	0:00	MCC	START OF PASSIVATION (PHASE YELLOW) (Write down Time)	Passivation	2
289	0:00	MCC	Turn audio volume up		2
290	0:00	TMTC	Check ROxTPT & RHPPT 1 Bar, if more: Open & Close STEPWISE RDV		2
291	0:00	MRL	Go to Testrig, Close N2O Bottle 1 & N2O Bottle 2 then RETURN to Block House		2
292	0:00	EGSE	Open OxDV		2
293	0:00	EGSE	Open OxV1		2
294	0:00	EGSE	Check OxInPT1 & OxOutPT 0 Bar		2
295	0:00	EGSE	Close OxV1		2
296	0:00	EGSE	Open OxV2		2
297	0:00	EGSE	Check OxInPT2 & OxOutPT 0 Bar		2
298	0:00	EGSE	Close OxV2		2
299	0:00	EGSE	Close OxDV		2
300	0:00	MRL	Close He Bottle 2		2
301	0:00	MRL	Write down remaining Pressure of He Bottle 2		2
302	0:00	EGSE	Open HPDV		2
303	0:00	EGSE	Open HPV2		2
304	0:00	EGSE	Check pressure HPLPT & HPPT2 0 Bar		2
305	0:00	EGSE	Close HPV2		2
306	0:00	EGSE	Close HPDV		2
307	0:00	MRL	Go to Testrig, confirm HPPG2 0 Bar, else return to Block House, THEN...		2
308	0:00	MRL	Close He Bottle 1		2
309	0:00	MRL	Open ComTerm		2
310	0:00	MRL	Write down remaining Pressure of He Bottle 1		2
311	0:00	MRL	Step back		2
312	0:00	EGSE	Open HPDV		2
313	0:00	EGSE	Open HPV1		2
314	0:00	EGSE	Check pressure HPLPT & HPPT1 0 Bar		2
315	0:00	EGSE	Close HPV1		2
316	0:00	EGSE	Close HPDV		2
317	0:00	EGSE	Pressure Check		2
318	0:00	MRL	Open MBV		2
319	0:00	EGSE	Check and compare pressure HPPT1 with HPPG1		2
320	0:00	MRL	Close MBV		2
321	0:00	MRL	Take out B1 & B2 Bridges		2
322	0:00	MRL	Safety is ensured		2
323	0:00	MCC	Confirm to OPS that Safety is ensured		1
324	0:00	MCC	END OF PASSIVATION (PHASE GREEN) (Write down Time)		1
325	0:00	MCC	START DATA COLLECTION (Write down Time)	Collection	1
326	0:00	AVC	Turn off GoPro & Camcorder & Stop Block House Video recording		1
327	0:00	EGSE	Copy PID.vi.tdms & save to new name		1
328	0:00	EGSE	Wait for buffer storage process to be finished		1
329	0:00	EGSE	save data files from cRIO to PC		1
330	0:00	AVC	End audio recording		1
331	0:00	MCC	END OF PROCEDURE (Write Down Time)		1
332	0:00	AVC	Save video & audio data on external HDD		1
333	0:00	MCC	Stop RT_CD.vi and save logfile to external HDD		1
334	0:00	MCC	PROCEDURE FINISHED	End	1