procedure/LaunchProcedure.csv

1	vers.	v4.29	Launch Procedure		0	MRL	MCC	RdHill	Time per step
2	147:20	MCC	BEGIN SEQUENCE: Power on EGSE	Power on EGSE	1
3	147:20	WIND	Start wind weighting analysis		1
4	147:20	EGSE	Check CLD connection		1
5	147:20	EGSE	Switch ON CLD via Battery & check voltage (24 Volt)		1
6	147:20	EGSE	Switch ON the primary and secondary supply switches on the Control Panel		1				01:00
7	146:20	EGSE @MRL	Switch ON Sup_24V_20A & check voltage (ca. 27,2 Volt)		1
8	146:20	EGSE @MRL	Switch ON Sup_24V_10A & check voltage (ca. 27,2 Volt)		1
9	146:20	EGSE @MRL	Switch ON Sup_12V_10A & check voltage (ca. 13,8 Volt)		1
10	146:20	EGSE @MRL	Switch ON Bat_24V_20A & check voltage (ca. 27,9 Volt)		1
11	146:20	EGSE @MRL	Switch ON Bat_24V_10A & check voltage (ca. 27,9 Volt)		1
12	146:20	EGSE @MRL	Switch ON Bat_12V_10A & check voltage (ca. 13,8 Volt)		1
13	146:20	EGSE @MRL	Switch ON Sup_24V_40A		1
14	146:20	EGSE @MRL	Switch ON Sup_5V_10A		1				03:00
15	143:20	EGSE	Connect to cRio		1
16	130:40	EGSE	Confirm storage capacity of cRio is greater than 300MB		1				00:10
17	143:20	EGSE	Start RT_VI		1
18	143:20	EGSE	Open PID-VI and confirm it is running		1
19	143:20	EGSE	Rename PID-Logfile		1				02:00
20	141:20	MCC	BEGIN SEQUENCE: Connect Data Umbilical	Connect Data Umbilical	1				00:30
21	141:20	MRL	Confirm working personel is grounded		1
22	141:20	EGSE @MRL	Confirm ALL 8 bridges on the right side are inserted		1
23	141:20	EGSE @MRL	Confirm ALL 8 bridges on the left side are removed		1
24	141:20	EGSE @MRL	Connect Data Umbilical		1
25	0:00	EGSE @MRL	Remove EXT_24V GROUND Bridge (1R)		1
26	0:00	EGSE @MRL	Remove MAIN_BUS GROUND Bridge (2R)		1
27	0:00	EGSE @MRL	Remove OBC2_BAT GROUND Bridge (4R)		1
28	0:00	EGSE @MRL	Remove PAYLOAD1 GROUND Bridge (5R)		1
29	0:00	EGSE @MRL	Remove RECOVERY_BAT GROUND Bridge (7R)		1
30	140:50	EGSE	Turn ON EGSE EPS_BAT		1
31	140:50	EGSE	Turn ON EGSE EXT_24V		1
32	0:00	EGSE @MRL	Insert EXT_24V Bridge (1L)		1
33	0:00	EGSE @MRL	Confirm EXT_24V LED is ON		1
34	0:00	EGSE @MRL	Insert MAIN_BUS Bridge (2L)		1
35	0:00	EGSE @MRL	Confirm MAIN_BUS LED is OFF (if ON pull MAIN_BUS Bridge (2L) & Insert all grounding Bridges on the right side		1
36	0:00	EGSE @MRL	Remove EPS RADIO SILENCE Bridge (3R)		1
37	0:00	EGSE	Turn OFF EGSE EPS_BAT		1
38	0:00	EGSE @MRL	Confirm MAIN_BUS LED is ON		1
39	0:00	EGSE @MRL	Confirm 1 beep at Telemega		1
40	140:50	OBDH	Clear SD-Card-using FileZilla FTP		1				01:00
41	139:50	OBDH	Connect to sbRio using remote Access utility		1
42	139:50	MRL	Confirm 3 beeps at OBC1		1
43	139:50	OBDH	Open RT_Sub_HMI		1
44	139:50	OBDH	Confirm Main Chute button is disabled		1
45	135:40	OBDH	Check EPS hardware Voltages		1				00:10
46	0:00	EGSE	Check EGSE Currents		1				00:10
47	139:50	WIND	Report on weather situation		1
48	139:50	MCC	BEGIN SEQUENCE: Connect Fueling arm	Connect Fueling Arm	1
49	139:50	MRL	Confirm working personel is grounded		1				01:00
50	139:50	MRL	Confirm PPG 0 bar		1
51	138:50	MRL	Remove Pneumatic Line from Fueling arm		1
52	138:50	MRL	Move Fueling arm to rocket		1
53	138:50	MRL	Couple Helium coupling		1
54	138:50	MRL	Couple N2O coupling		1
55	138:50	MRL	Reattach Pneumatic Line to Fueling arm		1				03:00
56	135:50	EGSE	BEGIN SEQUENCE: EGSE sensor and actuator test	EGSE sensor & actuator test	1
57	135:50	MCC	Confirm that video recording is enabled @ MCC		1				00:10
58	135:50	MRL	Confirm that Ignition Umbilical is disconnected		1
59	135:30	EGSE	Start PID data recording		1				00:10
60	135:20	MRL	Close HPNV1		1				00:10
61	135:20	MRL	Close HPNV2		1				00:10
62	135:10	EGSE/ MRL	Switch OxDV to closed & check if magnetic valve LED is on		1				00:10
63	135:00	EGSE/ MRL	Switch HPDV to closed & check if magnetic valve LED is on		1				00:10
64	134:50	EGSE/ MRL	Check warning lamp on HPSM		1				00:10
65	134:40	MRL	Remove loose equipment		1				03:00
66	131:40	EGSE	Activate Heizi		1				00:10
67	131:30	EGSE	Activate N2O_Heater 1		1				00:10
68	131:20	EGSE	Activate N2O_Heater 2		1				00:10
69	131:10	EGSE	Activate He_Heater		1				00:10
70	131:00	OBDH	Verify Heizi @ RDVT & RDVET		1				00:10
71	130:50	EGSE/ MRL	Check Bottle Temperatures @ OxT1, OxT2, HPT2. If above 30C aknowledge high temperature. If above 35C enter HOLD		1				00:10
72	130:40	EGSE/ MRL	Check Water Temperatures @ OxWT1, OxWT2, HPWT2		1				00:10
73	130:30	EGSE	Deactivate Heizi		1				00:10
74	130:20	EGSE/ MRL	Check OxV1 (CLD & RT_VI)		1				00:10
75	130:10	EGSE/ MRL	Check OxV2 (CLD & RT_VI)		1				00:10
76	130:00	EGSE/ MRL	Check MPV3 (CLD & RT_VI)		1				00:10
77	129:50	EGSE/ MRL	Check HPV1 (CLD & RT_VI)		1				00:10
78	129:40	EGSE/ MRL	Check HPV2 (CLD & RT_VI)		1				00:10
79	129:30	EGSE/ MRL	Check MPV1/2 (CLD & RT_VI)		1				00:10
80	129:20	EGSE/ MRL	Check RDV (CLD & RT_VI)		1				00:10
81	129:10	EGSE/ MRL	Check RMOxOV (CLD & RT_VI)		1				00:10
82	129:00	EGSE/ MRL	Check RMOxSV (CLD & RT_VI)		1				00:10
83	128:50	OBDH	Activate Heizi		1				00:10
84	128:40	OBDH	Verify Heizi @ RDVT & RDVET		1				01:00
85	127:40	OBDH/ MRL	Check RDV		1				00:10
86	127:30	OBDH/ MRL	Check RNCEV		1				00:10
87	127:20	OBDH/ MRL	Check RMOxOV		1				00:10
88	127:10	OBDH/ MRL	Check RMOxSV		1				00:10
89	127:00	OBDH/ MRL	Disable RNCEV		1				00:10
90	125:00	MRL	Confirm MBV closed		1
91	125:00	EGSE	Confirm that all valve switches are in OFF position (Except OxDV & HPDV)		1				00:10
92	115:00	MRL/ EGSE	Check loadcell by applying force to it		1				00:20
93	114:40	OBDH	Check RHPPT shows atmosphere		1
94	114:40	OBDH	Check ROxTPT shows atmosphere		1
95	114:40	OBDH	Check RIHPT shows atmosphere		1
96	114:40	OBDH	Check RCCPT shows atmosphere		1
97	114:40	OBDH	Check RBaro1 shows atmosphere		1
98	114:40	OBDH	Check RBaro2 shows atmosphere		1
99	114:40	EGSE	Check HPPT1 shows 0 bar		1				00:20
100	114:20	EGSE	Check HPPT2 shows 0 bar		1
101	114:20	EGSE	Check HPLPT shows 0 bar		1
102	114:20	EGSE	Check OxInPT1 shows 0 bar		1
103	114:20	EGSE	Check OxInPT2 shows 0 bar		1
104	114:20	EGSE	Check OxOutPT shows 0 bar		1				00:20
105	114:00	EGSE/ MRL	Switch on N2O coupling & check if magnetic valve LED is on		1
106	114:00	EGSE/ MRL	Switch on He coupling & check if magnetic valve LED is on		1
107	114:00	EGSE/ MRL	Switch on swivle arm & check if magnetic valve LED is on		1
108	114:00	EGSE	Switch off swivel arm & He coupling & N2O coupling		1				01:00
109	114:00	MCC	BEGIN SEQUENCE: Ignition signal Test	Ignition signal Test	1				01:00
110	113:00	MRL	Confirm that Ignition Umbilical is disconnected		1
111	113:00	MRL	Connect Ignition test receptical		1
112	113:00	EGSE @MRL	Plug in Bridges B1 and B2		1
113	113:00	MRL	Confirm Soundsignal from Ignition Umbilical		1
114	113:00	EGSE	Turn on Ignition Secure Switch		1
115	113:00	EGSE/ OBDH	Turn on Ignition Switch for 2 Second & Confirm ignition signal received at sbRio & cRio		1
116	113:00	EGSE	Confirm that Ignition Switch is switched OFF and secured		1
117	113:00	EGSE	Turn off Ignition Secure Switch		1
118	113:00	EGSE @MRL	Remove Bridges B1 and B2		1
119	113:00	MRL	Remove Ignition test receptical		1				03:00
120	113:00	MRL	Remove Ignition test receptical		1				03:00
121	110:00	MCC	BEGIN SEQUENCE: Ground segment pressure test (PHASE YELLOW)	GSE Pressure Test	2	LuF, AlS, LeD: 1x Helm, 3x Ear protectors	ChB, FiH, JuL, LiA, MiS
122	130:50	EGSE/ MRL	Check Bottle Temperatures @ OxT1, OxT2, HPT2. If above 30C aknowledge high temperature. If above 35C enter HOLD		2				00:10
123	130:40	EGSE/ MRL	Check Water Temperatures @ OxWT1, OxWT2, HPWT2		2				00:10
124	109:00	MRL	Confirm He bottle 1 connector is attached		2
125	109:00	MRL	Confirm He bottle 2 connector is attached		2
126	109:00	MRL	Confirm N2O bottle 1 connector is attached		2
127	109:00	MRL	Confirm N2O bottle 2 connector is attached		2
128	109:00	MRL	Confirm hose between HPSM & N2OSM is connected on both ends		2
129	109:00	MRL	Confirm hose between HPSM & Flight Segment is connected on both ends		2
130	109:00	MRL	Confirm hose between N2OSM & Flight Segment is connected on both ends		2
131	109:00	MRL	Confirm pneumatic hose is connected on both ends		2				02:00
132	107:00	MRL	Put on safety equipment		2
133	107:00	MRL	Confirm MBV is closed		2
134	107:00	MRL	Confirm HPNV1 is closed		2
135	107:00	MRL	Confirm HPNV2 is closed		2
136	107:00	MRL	Take positions to open He Bottle 1		2
137	107:00	EGSE	Confirm HPV1 is closed		2
138	107:00	EGSE	Confirm MPV1/2 is closed		2
139	107:00	MRL	Open He Bottle 1		2				01:00
140	106:00	MRL	Check & compare pressure HPPT1 with HPPG1 (max 300 bar)		2
141	106:00	MRL	Check Gastech Silver HPPR1 (max 300 to 50 bar)		2
142	106:00	MRL	Check Harris PPR (50 to 8 bar)		2
143	106:00	MRL	Check pneumatic PPG (8 bar)		2
144	106:00	MRL	Step back		2				01:00
145	105:00	EGSE/ MRL	Open & Close HPV1 SHORTLY & Check HPPT1		2
146	105:00	EGSE	Check HPPT1 300 Bar		2
147	105:00	EGSE	Confirm HPLPT 0 Bar		2
148	105:00	EGSE/ MRL	Open & Close HPV2 SHORTLY & Confirm HPPT2 0 bar		2
149	105:00	EGSE/ MRL	Open & Close HPDV SHORTLY & Confirm HPLPT 0 bar		2
150	105:00	EGSE/ MRL	Open & Close OxV1 SHORTLY		2
151	105:00	EGSE/ MRL	Open & Close OxV2 SHORTLY		2
152	105:00	EGSE/ MRL	Open & Close OxDV SHORTLY		2
153	105:00	EGSE/ MRL	Open & Close MPV3 SHORTLY		2
154	0:00	MRL	Open HPNV1 completely		2
155	0:00	MRL	Step Back		2
156	0:00	EGSE	Open & Close HPV1 STEPWISE untile HPLPT equal to HPPT1 and check for leakage @HPLPT (If leakage occurs proceed to passivation Procedure out of sequence)		2
157	0:00	EGSE	Close HPV1		2
158	0:00	EGSE	Open HPDV & confirm HPLPT 0 Bar		2
159	0:00	EGSE	Open HPV2 & confirm HPPT2 0 Bar		2
160	0:00	EGSE	Close HPV2		2
161	0:00	EGSE	Close HPDV		2
162	87:10	EGSE	Open & Close STEPWISE MPV1/2 to 50 Bar @ OxInPT1 & OxInPT2		2
163	87:10	EGSE	Confirm MPV1/2 closed		2
164	87:10	EGSE	Open OxDV		2
165	87:10	EGSE	Open & Close STEPWISE MPV3 to 0 Bar @OxOutPT		2
166	87:10	EGSE	Check OxInPT1 and OxInPT2 for leakage (If leakage occurs proceed to passivation Procedure out of sequence)		2
167	87:10	EGSE	Confirm MPV3 closed		2
168	87:10	EGSE	Open & Close STEPWISE OxV1 to 0 Bar @OxInPT1		2
169	87:10	EGSE	Open & Close STEPWISE OxV2 to 0 Bar @OxInPT2		2
170	87:10	EGSE	Confirm OxOutPT 0 Bar		2
171	87:10	EGSE	Close OxDV		2
172	105:00	EGSE	Confirm HPLPT & OxOutPT 0 Bar		2				01:30
173	103:30	EGSE	Decouple N2O coupling		2
174	103:30	EGSE	Decouple Helium coupling		2				00:20
175	103:10	EGSE	Move arm away from rocket		2
176	103:10	EGSE	Move arm to rocket		2				01:00
177	102:10	MRL	Close He Bottle 1 and check HPSM for leakage (If leakage occurs proceed to passivation Procedure out of sequence)		2				01:00
178	101:10	MRL	Open MBV		2
179	101:10	EGSE/ MRL	Check and compare pressure HPPT1 with HPPG1 0 Bar		2
180	101:10	MRL	Close MBV		2				00:30
181	100:40	MRL	Safety is ensured		2
182	100:40	MCC	EGSE @MRL to MRL		1
183	100:40	EGSE	Switch OFF N20 coupling		1
184	100:40	EGSE	Switch OFF He coupling		1
185	100:40	MRL	Confirm working personel is grounded		1				01:00
186	100:40	MRL	Confirm PPG 0 Bar		1				00:20
187	100:40	MRL	Release Pneumatic lines of couplings		1				00:20
188	100:20	EGSE	Confirm Fueling arm is switched OFF		1
189	100:20	EGSE	Confirm OxOutPT and HPLPT 0 bar		1
190	100:20	MRL	Couple He coupling		1				00:30
191	99:50	MRL	Couple N2O coupling		1				00:30
192	99:50	MRL	Confirm He coupling is connected properly		1
193	99:50	MRL	Confirm N2O coupling is connected properly		1
194	130:50	EGSE/ MRL	Check Bottle Temperatures @ OxT1, OxT2, HPT2. If above 30C aknowledge high temperature. If above 35C enter HOLD		1				00:10
195	130:40	EGSE/ MRL	Check Water Temperatures @ OxWT1, OxWT2, HPWT2		1				00:10
196	99:20	MRL	HOLD	HOLD	1
197	99:20	MCC	CONTINUE AFTER HOLD		1
198	99:20	MRL	BEGIN SEQUENCE: On Board System Test	On Board System Test	2
199	130:50	EGSE/ MRL	Check Bottle Temperatures @ OxT1, OxT2, HPT2. If above 30C aknowledge high temperature. If above 35C enter HOLD		1				00:10
200	130:40	EGSE/ MRL	Check Water Temperatures @ OxWT1, OxWT2, HPWT2		1				00:10
201	99:40	OBDH	Check RDV		2				00:10
202	99:30	OBDH	Check RNCEV		2				00:10
203	99:20	OBDH	Check RMOxOV		2				00:10
204	99:10	OBDH	Check RMOxSV		2				00:10
205	99:00	OBDH	Disable RNCEV		2				00:10
206	0:00	MRL	Confirm working personel is grounded		2				01:00
207	0:00	OBDH	Disconnect from sbRio		1
208	0:00	EGSE	Turn ON EPS_BAT (Rocket OFF)		2				01:00
209	0:00	EGSE @MRL	Insert EPS RADIO SILENCE Bridge (3R)		1
210	0:00	EGSE @MRL	Insert MAIN_BAT Bridge (3L)		1
211	0:00	EGSE @MRL	Confirm MAIN_BAT LED is ON		1
212	0:00	EGSE @MRL	Insert OBC2_BAT Bridge (4L)		1
213	0:00	EGSE @MRL	Confirm OBC2_BAT LED is ON		1
214	0:00	EGSE @MRL	Insert RECOVERY_BAT Bridge (7L)		1
215	0:00	EGSE @MRL	Confirm RECOVERY_BAT LED is ON		1
216	0:00	EGSE @MRL	Insert PAYLOAD1 Bridge (5L)		1
217	0:00	EGSE @MRL	Confirm PAYLOAD1 LED is OFF		1
218	0:00	EGSE @MRL	Insert PAYLOAD2 Bridge (6L)		1
219	0:00	EGSE @MRL	Confirm PAYLOAD2 LED is ON		1
220	0:00	EGSE @MRL	Confirm MAIN_BUS LED is OFF		1
221	0:00	EGSE @MRL	Remove EPS RADIO SILENCE Bridge (3R)		1
222	0:00	EGSE	Turn OFF EPS_BAT (Rocket ON)		2				01:00
223	0:00	EGSE @MRL	Confirm MAIN_BUS LED is ON		1
224	0:00	EGSE @MRL	Confirm 1 beep at Telemega		1
225	0:00	EGSE @MRL	Remove BLACKBOX2 RADIO SILENCE Bridge (3R)		1
226	139:50	OBDH	Connect to sbRio using remote Access utility		1
227	139:50	MRL	Confirm 3 beeps at OBC1		1
228	139:50	OBDH	Open RT_Sub_HMI		1
229	139:50	OBDH	Confirm Main Chute button is disabled		1
230	135:40	OBDH	Check EPS hardware Voltages		1				00:10
231	0:00	EGSE	Check EGSE Currents		1				00:10
232	125:30	PYL	Confirm CanSat is running		3				00:20
233	125:30	PYL	Confirm BlackBox2 is running		3
234	0:00	OBDH	Disconnect from sbRio		1
235	99:20	EGSE	Turn ON EPS_BAT (Rocket OFF)		2				01:00
236	99:20	MRL	BEGIN SEQUENCE: Prime Rocket	Prime Rocket	2
237	99:20	EGSE	Confirm EPS_BAT is ON (Rocket OFF)		2				01:00
238	99:20	MRL	Confirm working personel is grounded		2				01:00
239	99:20	MRL	Confirm that RMDV is closed		2				01:00
240	99:00	MRL	Close & secure HP maintenance cover		2				01:00
241	99:00	MRL	Close & secure MainOX maintenance cover		2				01:00
242	98:50	MRL	Turn on GoPro Camera at end of Launch Rail		2				00:20
243	141:20	EGSE @MRL	Confirm ALL 8 bridges on the right side are removed		1
244	141:20	EGSE @MRL	Confirm ALL 8 bridges on the left side are inserted		1
245	95:30	MRL	Close & secure bridge maintenance cover		2				00:20
246	99:20	MRL	Confirm spring retracted cover at He coupling is moving freely		2
247	99:20	MRL	Confirm spring retracted cover at N2O coupling is moving freely		2
248	95:00	MRL	Confirm that HP maintenance cover is closed & secured		2				01:00
249	95:30	MRL	Confirm bridge maintenance cover is closed & secured		2				00:20
250	95:00	MRL	Confirm that MainOX maintenance cover is closed & secured		2				01:00
251	95:10	EGSE @MRL	Leave MRL & return to MCC		2
252	99:20	MRL	Connect Ignition Umbilical		2				00:30
253	95:10	OPS	Elevate MRL to 90 degrees		2				05:00
254	89:40	EGSE	Zero OxTank Mass		2				01:00
255	88:40	MCC	BEGIN SEQUENCE: Fueling Preparations (PHASE YELLOW)	Fueling Preparations	2
256	130:50	EGSE/ MRL	Check Bottle Temperatures @ OxT1, OxT2, HPT2. If above 30C aknowledge high temperature. If above 35C enter HOLD		2				00:10
257	130:40	EGSE/ MRL	Check Water Temperatures @ OxWT1, OxWT2, HPWT2		2				00:10
258	88:40	MRL	Put on safety equipment		2				00:30
259	10:10	MRL	Confirm HPNV1 is Open		2
260	10:10	MRL	Confirm HPNV2 is Closed		2
261	88:10	MRL	Open He Bottle 1		2				01:00
262	87:10	MRL	Step back		2
263	0:00	EGSE	Open & Close HPV1 STEPWISE untile HPLPT equal to HPPT1 and check for leakage @HPLPT (If leakage occurs continue with "GSE Passivation Procedure")		2
264	0:00	EGSE	Open HPV1		2
265	0:00	EGSE	Open & Close HPV2 STEPWISE untile HPPT2 equal to HPLPT and check for leakage @HPPT2 (If leakage occurs continue with "GSE Passivation Procedure")		2
266	0:00	EGSE	Close HPV1		2
267	0:00	EGSE	Open HPDV & Confirm HPLPT 0 Bar		2
268	0:00	EGSE	Confirm HPV1 is closed		2
269	0:00	EGSE	Confirm HPV2 is closed		2
270	10:10	MRL	Open HPNV2 1/8 Rev		2
271	0:00	EGSE	Close HPDV		2
272	87:10	EGSE	Open & Close STEPWISE MPV1/2 to 50 Bar @ OxInPT1 & OxInPT2		2
273	87:10	EGSE/ MRL	Check & compare OxInPT1 with OxInPG1 based on Bottle temperature (max 50 bar)		2
274	87:10	EGSE/ MRL	Check & compare pressure OxInPT2 with OxInPG2 based on Bottle temperature (max 50 bar)		2
275	87:10	EGSE/ MRL	Check Temperature of N2O Bottle 1 @OxT1 & OxWT1 (max 22C)		2
276	87:10	EGSE/ MRL	Check Temperature of N2O Bottle 2 @OxT2 & OxWT2 (max 22C)		2				01:30
277	85:40	MRL	Open He Bottle 2		2
278	85:40	EGSE/ MRL	Check & compare pressure HPPT2 with HPPG2 (max 315 bar)		2				01:00
279	84:40	ALL/ MRL	CAUTION!		2
280	84:40	MRL	Open N2O Bottle 1		2
281	84:40	MRL/ EGSE	Check & compare pressure OxInPT 1 with OxInPG 1 (max 50 bar)		2				02:00
282	82:40	MRL	Open N2O Bottle 2		2
283	82:40	MRL/ EGSE	Check & compare pressure OxInPT 2 with OxInPG 2 (max 50 bar)		2				02:00
284	80:40	MRL	Insert Ignition Bridges B1 and B2 into EGSE		2				02:00
285	78:40	MRL	Confirm Soundsignal from Ignition Umbilical		2
286	78:40	MRL	Close ComTerm & Go to Block House		2
287	78:40	MCC	Turn OFF MRL confirm lock		2
288	78:40	ALL	Inform OPS to clear Launch Pad (Tel.: [!!!])		2				02:00
289	147:20	WIND	Start wind weighting analysis		2
290	130:50	EGSE/ MRL	Check Bottle Temperatures @ OxT1, OxT2, HPT2. If above 30C aknowledge high temperature. If above 35C enter HOLD		2				00:10
291	130:40	EGSE/ MRL	Check Water Temperatures @ OxWT1, OxWT2, HPWT2		2				00:10
292	68:40	MCC	HOLD	HOLD	2
293	68:40	KLP	Start Camera Karsten Lapp<70>hn		2
294	68:40	MCC	CONTINUE AFTER HOLD		2
295	130:50	EGSE/ MRL	Check Bottle Temperatures @ OxT1, OxT2, HPT2. If above 30C aknowledge high temperature. If above 35C enter HOLD		2				00:10
296	130:40	EGSE/ MRL	Check Water Temperatures @ OxWT1, OxWT2, HPWT2		2				00:10
297	130:40	EGSE	Confirm storage capacity of CRio is greater than 300MB		2				00:10
298	127:00	OBDH	Confirm RNCEV is disabled		2				00:10
299	68:40	MCC	BEGIN SEQUENCE Ox Fueling (PHASE RED)	Ox Fueling (PHASE RED)	3
300	68:50	WIND	Report on weather situation		3
301	68:40	MCC	Announce end of Radio Silence		3
302	68:40	EGSE	Turn OFF EPS_BAT (Rocket ON)		3
303	0:00	OBDH	Connect to sbRio using remote Access utility		1
304	0:00	MCC	Confirm 3 beeps at OBC1		1
305	0:00	OBDH	Open RT_Sub_HMI		1
306	0:00	OBDH	Confirm Main Chute button is disabled		1
307	0:00	OBDH	Check EPS hardware Voltages		1				00:10
308	0:00	EGSE	Check EGSE Currents		1				00:10
309	126:50	OBDH/ TMTC	Confirm RF451-Link		3				00:20
310	126:30	TMTC	Confirm GPS-lock		3				00:20
311	126:10	TMTC	Confirm Telemega-Link		3				00:20
312	125:50	OBDH	Test Connection to STX3		3				00:20
313	125:30	OBDH	Confirm that STX3 Packages are received by email		3				00:30
314	125:30	AVC	Turn on main TMTC screen		3				00:30
315	125:30	PYL	Confirm CanSat is running		3				00:20
316	125:30	PYL	Confirm BlackBox2 is running		3
317	125:30	MCC	Request Permission to begin fueling from OPS		3				03:00
318	68:40	OBDH	Acknowledge start of Fueling		3				01:00
319	67:40	EGSE	Open & Close HPV1 STEPWISE to 50 Bar @ ROxTPT (stop every 10 bar & check ROxTBT & ROxTTT (approx. ambiente temp)		3
320	67:40	EGSE	Confirm OxOutPT 0 Bar to check ROxCV tightness		3
321	67:40	EGSE	Open & Close HPV1 STEPWISE to more than 50 Bar @ RHPPT and confirm ROxTPT 50 Bar		3
322	67:40	EGSE	Confirm HPV1 is closed		3
323	67:40	OBDH	Open RDV SHORTLY, to check tightness @ RHPPT & ROxTPT (If leakages occur continue with Abort Procedure)		3
324	67:40	EGSE	Open MPV1/2		3
325	67:40	EGSE	Open & Close MPV3 STEPWISE to 50 Bar @ OxOutPT		3
326	67:40	EGSE	Close MPV1/2		3
327	67:40	EGSE	Check & compare OxOutPT with OxInPT1		3
328	67:40	EGSE	Check if RHPPT & ROxTPT more than OxInPT1, If less Open & Close HPV1		3
329	67:40	EGSE	Zero OxTank Mass		3
330	67:40	MCC	Write down Time		3
331	67:40	EGSE	Open OxV1		3				04:00
332	63:40	OBDH	Open & Close RDV STEPWISE until N2O bottle empty or 25kg OxTankMass, keep temperatures RDVT and RDVET above 10<31>C and Check delta ROxTPT and OxInPT1		3				30:00:00
333	33:40	EGSE	Verify Bottle Temperatures @ OxT1, OxT2, HPT2		3				00:10
334	33:40	EGSE	Verify Water Temperatures @ Ox@T1, OxWT2, HPWT2		3				00:10
335	33:40	EGSE	Close OxV1		3				00:10
336	33:30	EGSE	Check if Pressure rises in OxPT1, if Pressure rises relief via OxV1 or wait for Pressure relief valve		3				01:00
337	32:30	EGSE	Check & compare OxOutPT with OxInPT2		3
338	32:30	EGSE	Check & compare RHPPT & ROxTPT 50 Bar and more than OxInPT2, If less Open & Close HPV1		3
339	32:30	EGSE	Open OxV2		3
340	32:30	OBDH	Open & Close RDV STEPWISE to 25kg OxTankMass, keep temperatures RDVT and RDVET above 10<31>C and Check delta OxTPT and OxInPT1		3				20:00
341	12:30	EGSE	Close OxV2		3				00:10
342	12:20	EGSE	Check if Pressure rises in OxPT2, if Pressure rises relief via OxV2 or wait for Pressure relief valve		3				01:00
343	11:20	EGSE	Open OxDV STEPWISE until OxOutPT 0 Bar		3
344	11:20	OBDH	Check ROxCV for tightness @ ROxTPT		3
345	11:20	EGSE	Close OxDV		3				01:00
346	10:20	EGSE	Write down OxTankMass		3
347	33:40	EGSE	Verify He Bottle 2 Temperature @HPT2 & @HPWT2 (turn ON He_Heater if necessary)		3				00:10
348	10:20	MCC	Provide OxTankMass and temperature readings to Wind weighting station		3				00:30
349	9:50	EGSE	Confirm OxV1 & OxV2 closed		3
350	9:50	EGSE	Confirm OxOutPT 0 Bar		3
351	9:50	EGSE	Decouple N2O coupling		3				00:20
352	9:30	MCC	Confirm End of Oxidator Fueling to OPS		3				00:15
353	9:20	WIND	Start wind weighting analysis		3
354	9:15	OBDH/ TMTC	Check RF451-Link		3				00:20
355	8:55	TMTC	Check GPS-lock		3				00:20
356	8:35	TMTC	Check Telemega-Link		3				00:20
357	33:40	EGSE	Verify He Bottle 2 Temperature @HPT2 & @HPWT2 (turn ON/OFF He_Heater if necessary)		3				00:10
358	8:15	MCC	HOLD (Last possible scheduled HOLD)	HOLD	3
359	8:15	OPS	Align MRL to Launch Trajectory		3
360	8:15	MCC	Turn audio volume down		3
361	8:15	MCC	Turn OFF ComTerm step delay		3
362	8:15	ALL	Talk through Ignition Sequence		3
363	8:15	MCC	Wait for OPS to confirm final MRL adjustment		3
364	8:15	WIND	Report on weather situation		3
365	8:15	MCC	CONTINUE AFTER HOLD		3
366	8:15	AVC	Start Video recording in Block House		3
367	8:15	EGSE	Verify He Bottle 2 Temperature @HPT2 & @HPWT2 (turn ON/OFF He_Heater if necessary)		3				00:10
368	8:15	MCC	BEGIN SEQUENCE: Switching to Internal Power Sequence	Switch to Internal Power	3
369	8:15	EGSE	Turn OFF EPS_Ext (Switch to internal Power)		3				00:20
370	7:55	OBDH	Confirm EPS Voltages are within limits		3				00:10
371	7:45	OBDH	Confirm RF451 Transmitting		3				00:05
372	7:40	OBDH/ TMTC	Confirm RF451-Link		3				00:20
373	7:20	TMTC	Confirm GPS-lock		3				00:20
374	7:00	TMTC	Confirm Telemega-Link		3				00:20
375	6:40	OBDH	Switch to PREARMED		3				00:10
376	6:30	PYL	Confirm Payload is running		3				00:20
377	6:30	PYL	Confirm BlackBox2 is ready for launch		3
378	6:10	AVC	Confirm that videorecording @ MCC is running		3				00:05
379	6:05	MCC	BEGIN SEQUENCE: High Pressure Fueling	High Pressure Fueling	3
380	33:40	EGSE	Verify He Bottle 2 Temperature @HPT2 & @HPWT2 (turn ON/OFF He_Heater if necessary)		3				00:10
381	6:05	EGSE	Open & Close HPV1 STEPWISE until RHPPT 300 Bar or pressure equal to He Bottle 1		3
382	6:05	EGSE	Open & Close HPV2 STEPWISE until RHPPT 300 Bar		3
383	6:05	EGSE	Open & close HPDV STEPWISE until HPLPT 0 Bar		3
384	6:05	EGSE	Confirm HPDV closed		3
385	6:05	OBDH/ EGSE	Check for leakage & HPLPT 0 Bar & RHPPT 300 Bar		3				02:00
386	6:05	EGSE	Turn OFF He_Heater		3
387	4:05	OBDH	Acknowledge end of Fueling		3				00:10
388	3:55	MCC	Confirm End of Fueling to OPS		3				00:20
389	3:35	MCC	BEGIN SEQUENCE: Disconnecting Fueling Arm	Disconnecting Fueling Arm	3				00:10
390	3:25	EGSE	Confirm HPV1 & HPV2 closed		3				00:10
391	3:15	EGSE	Confirm HPLPT 0 Bar		3				00:10
392	3:05	EGSE	Decouple Helium coupling		3				00:20
393	2:45	EGSE	Confirm Helium coupling is disconnected		3				00:10
394	2:35	EGSE	Move fueling arm away from rocket		3				00:40
395	1:55	MCC	Confirm Fueling Arm away to OPS		3				00:15
396	1:40	MCC	Prepare for Launch		3				00:10
397	1:30	OBDH	Confirm ready for launch		3				00:10
398	1:20	EGSE	Confirm ready for launch		3				00:10
399	1:10	MCC	Set Go/No-Go System to Go		3				00:10
400	1:00	MCC	Wait for Authorization for Launch		3				00:00
401	1:00	MCC	BEGIN SEQUENCE: Ignition	Ignition Sequence	3				00:10
402	0:50	OBDH	T-50 ARM		3				00:05
403	0:40	OBDH	T-40 Confirm all status indicators green		3				00:05
404	0:30	OBDH	T-30 Disconnect from sbRio		3				00:30
405	0:10	EGSE	T-10 Turn on Ignition Secure		3				00:07
406	0:03	EGSE	T-3: Ignition		3				00:03
407	0:00	OBDH	T+0: Verify RMOxOV Open (Launched)		3				00:00
408	0:00	EGSE	T+1: Turn OFF Ignition		3
409	0:00	EGSE	T+5: Turn OFF Ignition Secure		3
410	0:00	OBDH	T+20: Verify RMOxOV Closed and RMOxSV Open (Cruise)		3
411	0:00	OBDH	T+50: Verify RNCEV Open (Drogue)		3
412	0:00	OBDH	T+310: Verify Main Chute Deployed and RDV Open (Main)		3
413	0:00	OBDH	T+600: Verify (Landed)		3
414	0:00	MCC	BEGIN SEQUENCE: PASSIVATION (PHASE YELLOW)	Passivation	2
415	68:40	MCC	Announce BEGIN of Radio Silence		2
416	0:00	MCC	Turn audio volume up		2
417	0:00	MRL	Go to MRL, THEN...		2
418	0:00	MRL	Close N2O Bottle 1 & N2O Bottle 2, THEN...		2
419	0:00	MRL	RETURN to Block House		2
420	0:00	EGSE	Open OxDV		2
421	0:00	EGSE	Open OxV1		2
422	0:00	EGSE	Confirm OxInPT1 & OxOutPT 0 Bar		2
423	0:00	EGSE	Close OxV1		2
424	0:00	EGSE	Open OxV2		2
425	0:00	EGSE	Confirm OxInPT2 & OxOutPT 0 Bar		2
426	0:00	EGSE	Close OxV2		2
427	0:00	EGSE	Close OxDV		2
428	0:00	MRL	Go to MRL, confirm OxInPG1 & OxInPG2 0 Bar, else RETURN to Block House, THEN...		2
429	0:00	MRL	Close He Bottle 2, THEN...		2
430	0:00	MRL	Write down remaining Pressure of He Bottle 2, THEN...		2
431	0:00	MRL	Return to Block House		2
432	0:00	EGSE	Open HPDV		2
433	0:00	EGSE	Open HPV2		2
434	0:00	EGSE	Confirm pressure HPLPT & HPPT2 0 Bar		2
435	0:00	EGSE	Close HPV2		2
436	0:00	EGSE	Close HPDV		2
437	0:00	MRL	Go to Testrig, confirm HPPG2 0 Bar, else return to Block House, THEN...		2
438	0:00	MRL	Close He Bottle 1, THEN ...		2
439	0:00	MRL	Open ComTerm		2
440	8:15	MCC	Turn ON ComTerm step delay		2
441	0:00	MRL	Write down remaining Pressure of He Bottle 1		2
442	0:00	MRL	Step back		2
443	0:00	EGSE	Open HPDV		2
444	0:00	EGSE	Open HPV1		2
445	0:00	EGSE	Confirm pressure HPLPT & HPPT1 0 Bar		2
446	0:00	EGSE	Close HPV1		2
447	0:00	EGSE	Close HPDV		2
448	0:00	EGSE	Pressure Check		2
449	0:00	MRL	Open MBV		2
450	0:00	EGSE/ MRL	Check and compare pressure HPPT1 with HPPG1		2
451	0:00	MRL	Close MBV		2
452	0:00	MRL	Take out B1 & B2 Bridges		2
453	0:00	MRL	Safety is ensured		2
454	0:00	MCC	Confirm to OPS that Safety is ensured		2
455	0:00	MCC	BEGIN SEQUENCE: Data collection	Data collection	1
456	0:00	AVC	Turn off GoPro & Camcorder & Stop Block House Video recording		1
457	0:00	EGSE	Copy PID.vi.tdms & save to new name		1
458	0:00	EGSE	Wait for buffer storage process to be finished		1
459	0:00	EGSE	save data files from cRio to PC		1
460	0:00	WIND	Save data on external HDD		1
461	0:00	TMTC	Stop TMTC Vi and save data on external HDD		1
462	0:00	AVC	End audio recording		1
463	0:00	MCC	Stop ComTerm and save logfile to external HDD, THEN...		1
464	0:00	MCC	Restart ComTerm VI		1
465	0:00	AVC	Save video & audio data on external HDD		1
466	0:00	MCC	END OF PROCEDURE	End	1