procedure/LaunchProcedure.csv

1	vers.	v4.23	Launch Procedure		0	MRL	MCC	RdHill	Time per step
2	147:20	MCC	BEGIN SEQUENCE: Power on EGSE	Power on EGSE	1
3	147:20	WIND	Start wind weighting analysis		1
4	147:20	EGSE	Check CLD connection		1
5	147:20	EGSE	Switch ON CLD via Battery & check voltage (24 Volt)		1
6	147:20	EGSE	Switch ON the primary and secondary supply switches on the Control Panel		1				01:00
7	146:20	EGSE @MRL	Switch ON Sup_24V_20A & check voltage (ca. 27,2 Volt)		1
8	146:20	EGSE @MRL	Switch ON Sup_24V_10A & check voltage (ca. 27,2 Volt)		1
9	146:20	EGSE @MRL	Switch ON Sup_12V_10A & check voltage (ca. 13,8 Volt)		1
10	146:20	EGSE @MRL	Switch ON Bat_24V_20A & check voltage (ca. 27,9 Volt)		1
11	146:20	EGSE @MRL	Switch ON Bat_24V_10A & check voltage (ca. 27,9 Volt)		1
12	146:20	EGSE @MRL	Switch ON Bat_12V_10A & check voltage (ca. 13,8 Volt)		1
13	146:20	EGSE @MRL	Switch ON Sup_24V_40A		1
14	146:20	EGSE @MRL	Switch ON Sup_5V_10A		1				03:00
15	143:20	EGSE	Connect to cRio		1
16	130:40	EGSE	Confirm storage capacity of cRio is greater than 300MB		1				00:10
17	143:20	EGSE	Start RT_VI		1
18	143:20	EGSE	Open PID-VI and confirm it is running		1
19	143:20	EGSE	Rename PID-Logfile		1				02:00
20	141:20	MCC	BEGIN SEQUENCE: Connect Data Umbilical	Connect Data Umbilical	1				00:30
21	141:20	MRL	Confirm working personel is grounded		1
22	141:20	EGSL @MRL	Confirm ALL 8 Grounding bridges are inserted		1
23	141:20	EGSL @MRL	Connect Data Umbilical		1
24	140:50	EGSE	Turn on EPS_BAT		1
25	140:50	EGSE	Turn on EPS_EXT		1
26	140:50	EGSE @MRL	Leave EPS_BAT inserted and remove the other 7 Grounding Bridges		1
27	140:50	EGSE @MRL	Insert EPS_EXT Fuse in Power Supply Control Panel		1
28	140:50	EGSE @MRL	Confirm green LED at EPS_EXT Fuse is on		1
29	140:50	EGSE @MRL	Insert Main_Bus Fuse in Power Supply Control Panel		1
30	140:50	EGSE @MRL	Confirm LED at Main_Bus Fuse is OFF. Else Pull fuse and insert all Grounding Bridges		1
31	140:50	EGSE @MRL	Set remaining Fuses (except Payload Fuse) and check for green LED		1
32	140:50	EGSE	Turn OFF EPS_BAT		1
33	140:50	EGSE @MRL	Confirm Main bus LED is on.		1
34	140:50	EGSE	Start EPS via EPS_ext		1
35	140:50	OBDH	Clear SD-Card-using FileZilla FTP		1				01:00
36	139:50	OBDH	Connect to sbRio		1
37	139:50	OBDH	Start RT_Main		1
38	139:50	MRL	Confirm 3 beeps at OBC1		1
39	139:50	OBDH	Open RT_Sub_HMI		1
40	139:50	OBDH	Confirm Main Chute button is disabled		1
41	139:50	EGSE @MRL	Insert Payload Fuse		1
42	139:50	EGSE @MRL	Confirm green LED at Payload Fuse is on		1
43	139:50	WIND	Report on weather situation		1
44	139:50	MCC	BEGIN SEQUENCE: Connect Fueling arm	Connect Fueling Arm	1
45	139:50	MRL	Confirm working personel is grounded		1				01:00
46	139:50	MRL	Confirm PPG 0 bar		1
47	138:50	MRL	Remove Pneumatic Line from Fueling arm		1
48	138:50	MRL	Move Fueling arm to rocket		1
49	138:50	MRL	Couple Helium coupling		1
50	138:50	MRL	Couple N2O coupling		1
51	138:50	MRL	Reattach Pneumatic Line to Fueling arm		1				03:00
52	135:50	EGSE	BEGIN SEQUENCE: EGSE sensor and actuator test	EGSE sensor & actuator test	1
53	135:50	MCC	Confirm that video recording is enabled @ MCC		1				00:10
54	135:50	MRL	Confirm that Ignition Umbilical is disconnected		1
55	135:40	OBDH	Check EPS hardware Voltages		1				00:10
56	135:30	EGSE	Start PID data recording		1				00:10
57	135:20	MRL	Close HPNV1		1				00:10
58	135:20	MRL	Close HPNV2		1				00:10
59	135:10	EGSE/ MRL	Switch OxDV to closed & check if magnetic valve LED is on		1				00:10
60	135:00	EGSE/ MRL	Switch HPDV to closed & check if magnetic valve LED is on		1				00:10
61	134:50	EGSE/ MRL	Check warning lamp on HPSM		1				00:10
62	134:40	MRL	Remove loose equipment		1				03:00
63	131:40	EGSE	Activate Heizi		1				00:10
64	131:30	EGSE	Activate N2O_Heater 1		1				00:10
65	131:20	EGSE	Activate N2O_Heater 2		1				00:10
66	131:10	EGSE	Activate He_Heater		1				00:10
67	131:00	OBDH	Verify Heizi @ RDVT & RDVET		1				00:10
68	130:50	EGSE/ MRL	Check Bottle Temperatures @ OxT1, OxT2, HPT2. If above 30C aknowledge high temperature. If above 35C enter HOLD		1				00:10
69	130:40	EGSE/ MRL	Check Water Temperatures @ OxWT1, OxWT2, HPWT2		1				00:10
70	130:30	EGSE	Deactivate Heizi		1				00:10
71	130:20	EGSE/ MRL	Check OxV1 (CLD & RT_VI)		1				00:10
72	130:10	EGSE/ MRL	Check OxV2 (CLD & RT_VI)		1				00:10
73	130:00	EGSE/ MRL	Check MPV3 (CLD & RT_VI)		1				00:10
74	129:50	EGSE/ MRL	Check HPV1 (CLD & RT_VI)		1				00:10
75	129:40	EGSE/ MRL	Check HPV2 (CLD & RT_VI)		1				00:10
76	129:30	EGSE/ MRL	Check MPV1/2 (CLD & RT_VI)		1				00:10
77	129:20	EGSE/ MRL	Check RDV (CLD & RT_VI)		1				00:10
78	129:10	EGSE/ MRL	Check RMOxOV (CLD & RT_VI)		1				00:10
79	129:00	EGSE/ MRL	Check RMOxSV (CLD & RT_VI)		1				00:10
80	128:50	OBDH	Activate Heizi		1				00:10
81	128:40	OBDH	Verify Heizi @ RDVT & RDVET		1				01:00
82	127:40	OBDH/ MRL	Check RDV		1				00:10
83	127:30	OBDH/ MRL	Check RNCEV		1				00:10
84	127:20	OBDH/ MRL	Check RMOxOV		1				00:10
85	127:10	OBDH/ MRL	Check RMOxSV		1				00:10
86	127:00	OBDH/ MRL	Disable RNCEV		1				00:10
87	125:00	MRL	Confirm MBV closed		1
88	125:00	EGSE	Confirm that all valve switches are in OFF position (Except OxDV & HPDV)		1				00:10
89	115:00	MRL/ EGSE	Check loadcell by applying force to it		1				00:20
90	114:40	OBDH	Check RHPPT shows atmosphere		1
91	114:40	OBDH	Check ROxTPT shows atmosphere		1
92	114:40	OBDH	Check RIHPT shows atmosphere		1
93	114:40	OBDH	Check RCCPT shows atmosphere		1
94	114:40	OBDH	Check RBaro1 shows atmosphere		1
95	114:40	OBDH	Check RBaro2 shows atmosphere		1
96	114:40	EGSE	Check HPPT1 shows 0 bar		1				00:20
97	114:20	EGSE	Check HPPT2 shows 0 bar		1
98	114:20	EGSE	Check HPLPT shows 0 bar		1
99	114:20	EGSE	Check OxInPT1 shows 0 bar		1
100	114:20	EGSE	Check OxInPT2 shows 0 bar		1
101	114:20	EGSE	Check OxOutPT shows 0 bar		1				00:20
102	114:00	EGSE/ MRL	Switch on N2O coupling & check if magnetic valve LED is on		1
103	114:00	EGSE/ MRL	Switch on He coupling & check if magnetic valve LED is on		1
104	114:00	EGSE/ MRL	Switch on swivle arm & check if magnetic valve LED is on		1
105	114:00	EGSE	Switch off swivel arm & He coupling & N2O coupling		1				01:00
106	114:00	MCC	BEGIN SEQUENCE: Ignition signal Test	Ignition signal Test	1				01:00
107	113:00	MRL	Confirm that Ignition Umbilical is disconnected		1
108	113:00	MRL	Connect Ignition test receptical		1
109	113:00	EGSE @MRL	Plug in Bridges B1 and B2		1
110	113:00	MRL	Confirm Soundsignal from Ignition Umbilical		1
111	113:00	EGSE	Turn on Ignition Secure Switch		1
112	113:00	EGSE/ OBDH	Turn on Ignition Switch for 2 Second & Confirm ignition signal received at sbRio & cRio		1
113	113:00	EGSE	Confirm that Ignition Switch is switched OFF and secured		1
114	113:00	EGSE	Turn off Ignition Secure Switch		1
115	113:00	EGSE @MRL	Remove Bridges B1 and B2		1
116	113:00	MRL	Remove Ignition test receptical		1				03:00
117	110:00	MCC	BEGIN SEQUENCE: Ground segment pressure test (PHASE YELLOW)	GSE Pressure Test	2	LuF, AlS, LeD: 1x Helm, 3x Ear protectors	ChB, FiH, JuL, LiA, MiS
118	130:50	EGSE/ MRL	Check Bottle Temperatures @ OxT1, OxT2, HPT2. If above 30C aknowledge high temperature. If above 35C enter HOLD		2				00:10
119	130:40	EGSE/ MRL	Check Water Temperatures @ OxWT1, OxWT2, HPWT2		2				00:10
120	110:00	MRL	Confirm that all hatches are closed		2				01:00
121	109:00	MRL	Confirm He bottle 1 connector is attached		2
122	109:00	MRL	Confirm He bottle 2 connector is attached		2
123	109:00	MRL	Confirm N2O bottle 1 connector is attached		2
124	109:00	MRL	Confirm N2O bottle 2 connector is attached		2
125	109:00	MRL	Confirm hose between HPSM & N2OSM is connected on both ends		2
126	109:00	MRL	Confirm hose between HPSM & Flight Segment is connected on both ends		2
127	109:00	MRL	Confirm hose between N2OSM & Flight Segment is connected on both ends		2
128	109:00	MRL	Confirm pneumatic hose is connected on both ends		2				02:00
129	107:00	MRL	Put on safety equipment		2
130	107:00	MRL	Confirm MBV is closed		2
131	107:00	MRL	Confirm HPNV1 is closed		2
132	107:00	MRL	Confirm HPNV2 is closed		2
133	107:00	MRL	Take positions to open He Bottle 1		2
134	107:00	EGSE	Confirm HPV1 is closed		2
135	107:00	EGSE	Confirm MPV1/2 is closed		2
136	107:00	MRL	Open He Bottle 1		2				01:00
137	106:00	MRL	Check & compare pressure HPPT1 with HPPG1 (max 300 bar)		2
138	106:00	MRL	Check Gastech Silver HPPR1 (max 300 to 50 bar)		2
139	106:00	MRL	Check Harris PPR (50 to 8 bar)		2
140	106:00	MRL	Check pneumatic PPG (8 bar)		2
141	106:00	MRL	Step back		2				01:00
142	105:00	EGSE/ MRL	Open & Close HPV1 SHORTLY & Check HPPT1		2
143	105:00	EGSE	Check HPPT1 300 Bar		2
144	105:00	EGSE	Confirm HPLPT 0 Bar		2
145	105:00	EGSE/ MRL	Open & Close HPV2 SHORTLY & Confirm HPPT2 0 bar		2
146	105:00	EGSE/ MRL	Open & Close HPDV SHORTLY & Confirm HPLPT 0 bar		2
147	105:00	EGSE/ MRL	Open & Close OxV1 SHORTLY		2
148	105:00	EGSE/ MRL	Open & Close OxV2 SHORTLY		2
149	105:00	EGSE/ MRL	Open & Close OxDV SHORTLY		2
150	105:00	EGSE/ MRL	Open & Close MPV3 SHORTLY		2
151	0:00	MRL	Open HPNV1 completely		2
152	0:00	MRL	Step Back		2
153	0:00	EGSE	Open & Close HPV1 STEPWISE untile HPLPT equal to HPPT1 and check for leakage @HPLPT (If leakage occurs continue with "GSE Passivation Procedure")		2
154	0:00	EGSE	Confirm RHPPT & RoxTPT 1 Bar (on Pressure continue with "Rocket Passivation Procedure")		2
155	0:00	EGSE	Open HPV1		2
156	0:00	EGSE	Open & Close HPV2 STEPWISE untile HPPT2 equal to HPLPT and check for leakage @HPPT2 (If leakage occurs continue with "GSE Passivation Procedure")		2
157	0:00	EGSE	Close HPV1		2
158	0:00	EGSE	Open HPDV & confirm HPLPT 0 Bar		2
159	0:00	EGSE	Open HPV2 & confirm HPPT2 0 Bar		2
160	0:00	EGSE	Close HPV2		2
161	0:00	EGSE	Close HPDV		2
162	87:10	EGSE	Open & Close STEPWISE MPV1/2 to 50 Bar @ OxInPT1 & OxInPT2		2
163	87:10	EGSE	Confirm MPV1/2 closed		2
164	87:10	EGSE	Open OxDV		2
165	87:10	EGSE	Open & Close STEPWISE MPV3 to 0 Bar @OxOutPT		2
166	87:10	EGSE	Check OxInPT1 and OxInPT2 for leakage (If leakage occurs proceed to GSE passivation Procedure)		2
167	87:10	EGSE	Confirm MPV3 closed		2
168	87:10	EGSE	Open & Close STEPWISE OxV1 to 0 Bar @OxInPT1		2
169	87:10	EGSE	Open & Close STEPWISE OxV2 to 0 Bar @OxInPT2		2
170	87:10	EGSE	Confirm OxOutPT 0 Bar		2
171	87:10	EGSE	Close OxDV		2
172	105:00	EGSE	Confirm HPLPT & OxOutPT 0 Bar		2				01:30
173	103:30	EGSE	Decouple N2O coupling		2
174	103:30	EGSE	Decouple Helium coupling		2				00:20
175	103:10	EGSE	Move arm away from rocket		2
176	103:10	EGSE	Move arm to rocket		2				01:00
177	102:10	MRL	Close He Bottle 1 and check HPSM for leakage (If leakage occurs continue with Passivation Procedure)		2				01:00
178	101:10	MRL	Open MBV		2
179	101:10	EGSE/ MRL	Check and compare pressure HPPT1 with HPPG1 0 Bar		2
180	101:10	MRL	Close MBV		2				00:30
181	100:40	MRL	Open RMDV & relief pressure		2
182	100:40	MRL	Close RMDV		2
183	100:40	MRL	Safety is ensured		2
184	100:40	MCC	EGSE @MRL to MRL		1
185	100:40	EGSE	Switch OFF N20 coupling		1
186	100:40	EGSE	Switch OFF He coupling		1
187	100:40	MRL	Confirm working personel is grounded		1				01:00
188	100:40	MRL	Confirm PPG 0 Bar		1				00:20
189	100:40	MRL	Release Pneumatic lines of couplings		1				00:20
190	100:20	EGSE	Confirm Fueling arm is switched OFF		1
191	100:20	EGSE	Confirm OxOutPT and HPLPT 0 bar		1
192	100:20	MRL	Couple He coupling		1				00:30
193	99:50	MRL	Couple N2O coupling		1				00:30
194	99:50	MRL	Confirm He coupling is connected properly		1
195	99:50	MRL	Confirm N2O coupling is connected properly		1
196	130:50	EGSE/ MRL	Check Bottle Temperatures @ OxT1, OxT2, HPT2. If above 30C aknowledge high temperature. If above 35C enter HOLD		1				00:10
197	130:40	EGSE/ MRL	Check Water Temperatures @ OxWT1, OxWT2, HPWT2		1				00:10
198	99:20	MRL	HOLD	HOLD	1
199	99:20	MCC	CONTINUE AFTER HOLD		1
200	130:50	EGSE/ MRL	Check Bottle Temperatures @ OxT1, OxT2, HPT2. If above 30C aknowledge high temperature. If above 35C enter HOLD		1				00:10
201	130:40	EGSE/ MRL	Check Water Temperatures @ OxWT1, OxWT2, HPWT2		1				00:10
202	99:20	MRL	BEGIN SEQUENCE: Prime Rocket	Prime Rocket	2
203	99:20	EGSE	Turn ON EPS_BAT		2				01:00
204	99:20	MRL	Confirm working personel is grounded		2				01:00
205	99:20	MRL	Confirm all spring retracted hatches are moving freely		2
206	98:50	MRL	Turn on GoPro Camera at end of Launch Rail		2				00:20
207	99:20	MRL	Connect Ignition Umbilical		2				00:30
208	98:30	MRL	Insert all EPS Bridges		2				03:00
209	95:30	MRL	Confirm Bridge Hatch is Secured		2				00:20
210	95:10	EGSE @MRL	return to MCC		2
211	95:10	OPS	Elevate MRL to 90 degrees		2				05:00
212	89:40	EGSE	Zero OxTank Mass		2				01:00
213	88:40	MCC	BEGIN SEQUENCE: Fueling Preparations (PHASE YELLOW)	Fueling Preparations	2
214	130:50	EGSE/ MRL	Check Bottle Temperatures @ OxT1, OxT2, HPT2. If above 30C aknowledge high temperature. If above 35C enter HOLD		2				00:10
215	130:40	EGSE/ MRL	Check Water Temperatures @ OxWT1, OxWT2, HPWT2		2				00:10
216	127:40	OBDH	!!!Check RDV		2				00:10
217	127:30	OBDH	!!!Check RNCEV		2				00:10
218	127:20	OBDH	!!!Check RMOxOV		2				00:10
219	127:10	OBDH	!!!Check RMOxSV		2				00:10
220	127:00	OBDH	!!!Disable RNCEV		2				00:10
221	88:40	MRL	Put on safety equipment		2				00:30
222	10:10	MRL	Confirm HPNV1 is Open		2
223	10:10	MRL	Confirm HPNV2 is Closed		2
224	88:10	MRL	Open He Bottle 1		2				01:00
225	87:10	MRL	Step back		2
226	0:00	EGSE	Open & Close HPV1 STEPWISE untile HPLPT equal to HPPT1 and check for leakage @HPLPT (If leakage occurs continue with "GSE Passivation Procedure")		2
227	0:00	EGSE	Open HPV1		2
228	0:00	EGSE	Open & Close HPV2 STEPWISE untile HPPT2 equal to HPLPT and check for leakage @HPPT2 (If leakage occurs continue with "GSE Passivation Procedure")		2
229	0:00	EGSE	Close HPV1		2
230	0:00	EGSE	Open HPDV & Confirm HPLPT 0 Bar		2
231	0:00	EGSE	Confirm HPV1 is closed		2
232	0:00	EGSE	Confirm HPV2 is closed		2
233	10:10	MRL	Open HPNV2 1/8 Rev		2
234	0:00	EGSE	Close HPDV		2
235	87:10	EGSE	Open & Close STEPWISE MPV1/2 to 50 Bar @ OxInPT1 & OxInPT2		2
236	87:10	EGSE/ MRL	Check & compare OxInPT1 with OxInPG1 based on Bottle temperature (max 50 bar)		2
237	87:10	EGSE/ MRL	Check & compare pressure OxInPT2 with OxInPG2 based on Bottle temperature (max 50 bar)		2
238	87:10	EGSE/ MRL	Check Temperature of N2O Bottle 1 @OxT1 & OxWT1 (max 22C)		2
239	87:10	EGSE/ MRL	Check Temperature of N2O Bottle 2 @OxT2 & OxWT2 (max 22C)		2				01:30
240	85:40	MRL	Open He Bottle 2		2
241	85:40	EGSE/ MRL	Check & compare pressure HPPT2 with HPPG2 (max 315 bar)		2				01:00
242	84:40	ALL/ MRL	CAUTION!		2
243	84:40	MRL	Open N2O Bottle 1		2
244	84:40	MRL/ EGSE	Check & compare pressure OxInPT 1 with OxInPG 1 (max 50 bar)		2				02:00
245	82:40	MRL	Open N2O Bottle 2		2
246	82:40	MRL/ EGSE	Check & compare pressure OxInPT 2 with OxInPG 2 (max 50 bar)		2				02:00
247	80:40	MRL	Insert Ignition Bridges B1 and B2 into EGSE		2				02:00
248	78:40	MRL	Confirm Soundsignal from Ignition Umbilical		2
249	78:40	MRL	Close ComTerm & Go to Block House		2
250	78:40	MCC	Turn OFF MRL confirm lock		2
251	78:40	ALL	Inform OPS to clear Launch Pad (Tel.: [!!!])		2				02:00
252	147:20	WIND	Start wind weighting analysis		2
253	130:50	EGSE/ MRL	Check Bottle Temperatures @ OxT1, OxT2, HPT2. If above 30C aknowledge high temperature. If above 35C enter HOLD		2				00:10
254	130:40	EGSE/ MRL	Check Water Temperatures @ OxWT1, OxWT2, HPWT2		2				00:10
255	68:40	MCC	HOLD	HOLD	2
256	68:40	KLP	Start Camera Karsten Lapp<70>hn		2
257	68:40	MCC	CONTINUE AFTER HOLD		2
258	130:50	EGSE/ MRL	Check Bottle Temperatures @ OxT1, OxT2, HPT2. If above 30C aknowledge high temperature. If above 35C enter HOLD		2				00:10
259	130:40	EGSE/ MRL	Check Water Temperatures @ OxWT1, OxWT2, HPWT2		2				00:10
260	130:40	EGSE	Confirm storage capacity of CRio is greater than 300MB		2				00:10
261	127:00	OBDH	Confirm RNCEV is disabled		2				00:10
262	68:40	MCC	BEGIN SEQUENCE Ox Fueling (PHASE RED)	Ox Fueling (PHASE RED)	3
263	68:50	WIND	Report on weather situation		3
264	68:40	MCC	Announce end of Radio Silence		3
265	68:40	EGSE	Turn OFF EPS_BAT		3
266	126:50	OBDH/ TMTC	Confirm RF451-Link		3				00:20
267	126:30	TMTC	Confirm GPS-lock		3				00:20
268	126:10	TMTC	Confirm Telemega-Link		3				00:20
269	125:50	OBDH	Test Connection to STX3		3				00:20
270	125:30	OBDH	Confirm that STX3 Packages are received by email		3				00:30
271	125:30	AVC	Turn on main TMTC screen		3				00:30
272	125:30	MCC	Request Permission to begin fueling from OPS		3				03:00
273	68:40	OBDH	Acknowledge start of Fueling		3				01:00
274	67:40	EGSE	Open & Close HPV1 STEPWISE to 50 Bar @ ROxTPT (stop every 10 bar & check ROxTBT & ROxTTT (approx. ambiente temp)		3
275	67:40	EGSE	Confirm OxOutPT 0 Bar to check ROxCV tightness		3
276	67:40	EGSE	Open & Close HPV1 STEPWISE to more than 50 Bar @ RHPPT and confirm ROxTPT 50 Bar		3
277	67:40	EGSE	Confirm HPV1 is closed		3
278	67:40	OBDH	Open RDV SHORTLY, to check tightness @ RHPPT & ROxTPT (If leakages occur continue with Abort Procedure)		3
279	67:40	EGSE	Open MPV1/2		3
280	67:40	EGSE	Open & Close MPV3 STEPWISE to 50 Bar @ OxOutPT		3
281	67:40	EGSE	Close MPV1/2		3
282	67:40	EGSE	Check & compare OxOutPT with OxInPT1		3
283	67:40	EGSE	Check if RHPPT & ROxTPT more than OxInPT1, If less Open & Close HPV1		3
284	67:40	EGSE	Zero OxTank Mass		3
285	67:40	MCC	Write down Time		3
286	67:40	EGSE	Open OxV1		3				04:00
287	63:40	OBDH	Open & Close RDV STEPWISE until N2O bottle empty or 25kg OxTankMass, keep temperatures RDVT and RDVET above 10<31>C and Check delta ROxTPT and OxInPT1		3				30:00:00
288	33:40	EGSE	Verify Bottle Temperatures @ OxT1, OxT2, HPT2		3				00:10
289	33:40	EGSE	Verify Water Temperatures @ Ox@T1, OxWT2, HPWT2		3				00:10
290	33:40	EGSE	Close OxV1		3				00:10
291	33:30	EGSE	Check if Pressure rises in OxPT1, if Pressure rises relief via OxV1 or wait for Pressure relief valve		3				01:00
292	32:30	EGSE	Check & compare OxOutPT with OxInPT2		3
293	32:30	EGSE	Check & compare RHPPT & ROxTPT 50 Bar and more than OxInPT2, If less Open & Close HPV1		3
294	32:30	EGSE	Open OxV2		3
295	32:30	OBDH	Open & Close RDV STEPWISE to 25kg OxTankMass, keep temperatures RDVT and RDVET above 10<31>C and Check delta OxTPT and OxInPT1		3				20:00
296	12:30	EGSE	Close OxV2		3				00:10
297	12:20	EGSE	Check if Pressure rises in OxPT2, if Pressure rises relief via OxV2 or wait for Pressure relief valve		3				01:00
298	11:20	EGSE	Open OxDV STEPWISE until OxOutPT 0 Bar		3
299	11:20	OBDH	Check ROxCV for tightness @ ROxTPT		3
300	11:20	EGSE	Close OxDV		3				01:00
301	10:20	EGSE	Write down OxTankMass		3
302	33:40	EGSE	Verify He Bottle 2 Temperature @HPT2 & @HPWT2 (turn ON He_Heater if necessary)		3				00:10
303	10:20	MCC	Provide OxTankMass and temperature readings to Wind weighting station		3				00:30
304	9:50	EGSE	Confirm OxV1 & OxV2 closed		3
305	9:50	EGSE	Confirm OxOutPT 0 Bar		3
306	9:50	EGSE	Decouple N2O coupling		3				00:20
307	9:30	MCC	Confirm End of Oxidator Fueling to OPS		3				00:15
308	9:20	WIND	Start wind weighting analysis		3
309	9:15	OBDH/ TMTC	Check RF451-Link		3				00:20
310	8:55	TMTC	Check GPS-lock		3				00:20
311	8:35	TMTC	Check Telemega-Link		3				00:20
312	33:40	EGSE	Verify He Bottle 2 Temperature @HPT2 & @HPWT2 (turn ON/OFF He_Heater if necessary)		3				00:10
313	8:15	MCC	HOLD (Last possible scheduled HOLD)	HOLD	3
314	8:15	OPS	Align MRL to Launch Trajectory		3
315	8:15	MCC	Turn audio volume down		3
316	8:15	MCC	Turn OFF ComTerm step delay		3
317	8:15	ALL	Talk through Ignition Sequence		3
318	8:15	MCC	Wait for OPS to confirm final MRL adjustment		3
319	8:15	WIND	Report on weather situation		3
320	8:15	MCC	CONTINUE AFTER HOLD		3
321	8:15	AVC	Start Video recording in Block House		3
322	8:15	EGSE	Verify He Bottle 2 Temperature @HPT2 & @HPWT2 (turn ON/OFF He_Heater if necessary)		3				00:10
323	8:15	MCC	BEGIN SEQUENCE: Switching to Internal Power Sequence	Switch to Internal Power	3
324	8:15	EGSE	Turn OFF EPS_Ext (Switch to internal Power)		3				00:20
325	7:55	OBDH	Confirm EPS Voltages are within limits		3				00:10
326	7:45	OBDH	Confirm RF451 Transmitting		3				00:05
327	7:40	OBDH/ TMTC	Confirm RF451-Link		3				00:20
328	7:20	TMTC	Confirm GPS-lock		3				00:20
329	7:00	TMTC	Confirm Telemega-Link		3				00:20
330	6:40	OBDH	Switch to PREARMED		3				00:10
331	6:30	PYL	Confirm Payload is running		3				00:20
332	6:30	PYL	Confirm BlackBox2 is ready for launch		3
333	6:10	AVC	Confirm that videorecording @ MCC is running		3				00:05
334	6:05	MCC	BEGIN SEQUENCE: High Pressure Fueling	High Pressure Fueling	3
335	33:40	EGSE	Verify He Bottle 2 Temperature @HPT2 & @HPWT2 (turn ON/OFF He_Heater if necessary)		3				00:10
336	6:05	EGSE	Open & Close HPV1 STEPWISE until RHPPT 300 Bar or pressure equal to He Bottle 1		3
337	6:05	EGSE	Open & Close HPV2 STEPWISE until RHPPT 300 Bar		3
338	6:05	EGSE	Open & close HPDV STEPWISE until HPLPT 0 Bar		3
339	6:05	EGSE	Confirm HPDV closed		3
340	6:05	OBDH/ EGSE	Check for leakage & HPLPT 0 Bar & RHPPT 300 Bar		3				02:00
341	6:05	EGSE	Turn OFF He_Heater		3
342	4:05	OBDH	Acknowledge end of Fueling		3				00:10
343	3:55	MCC	Confirm End of Fueling to OPS		3				00:20
344	3:35	MCC	BEGIN SEQUENCE: Disconnecting Fueling Arm	Disconnecting Fueling Arm	3				00:10
345	3:25	EGSE	Confirm HPV1 & HPV2 closed		3				00:10
346	3:15	EGSE	Confirm HPLPT 0 Bar		3				00:10
347	3:05	EGSE	Decouple Helium coupling		3				00:20
348	2:45	EGSE	Confirm Helium coupling is disconnected		3				00:10
349	2:35	EGSE	Move fueling arm away from rocket		3				00:40
350	1:55	MCC	Confirm Fueling Arm away to OPS		3				00:15
351	1:40	MCC	Prepare for Launch		3				00:10
352	1:30	OBDH	Confirm ready for launch		3				00:10
353	1:20	EGSE	Confirm ready for launch		3				00:10
354	1:10	MCC	Set Go/No-Go System to Go		3				00:10
355	1:00	MCC	Wait for Authorization for Launch		3				00:00
356	1:00	MCC	BEGIN SEQUENCE: Ignition	Ignition Sequence	3				00:10
357	0:50	OBDH	T-50 ARM		3				00:05
358	0:40	OBDH	T-40 Confirm all status indicators green		3				00:05
359	0:30	OBDH	T-30 Disconnect from sbRio		3				00:30
360	0:10	EGSE	T-10 Turn on Ignition Secure		3				00:07
361	0:03	EGSE	T-3: Ignition		3				00:03
362	0:00	OBDH	T+0: Verify RMOxOV Open (Launched)		3				00:00
363	0:00	EGSE	T+1: Turn OFF Ignition		3
364	0:00	EGSE	T+5: Turn OFF Ignition Secure		3
365	0:00	OBDH	T+20: Verify RMOxOV Closed and RMOxSV Open (Cruise)		3
366	0:00	OBDH	T+50: Verify RNCEV Open (Drogue)		3
367	0:00	OBDH	T+310: Verify Main Chute Deployed and RDV Open (Main)		3
368	0:00	OBDH	T+600: Verify (Landed)		3
369	0:00	MCC	BEGIN SEQUENCE: PASSIVATION (PHASE YELLOW)	Passivation	2
370	68:40	MCC	Announce BEGIN of Radio Silence		2
371	0:00	MCC	Turn audio volume up		2
372	0:00	MRL	Go to MRL, Close N2O Bottle 1 & N2O Bottle 2, THEN...		2
373	0:00	MRL	RETURN to Block House		2
374	0:00	EGSE	Open OxDV		2
375	0:00	EGSE	Open OxV1		2
376	0:00	EGSE	Confirm OxInPT1 & OxOutPT 0 Bar		2
377	0:00	EGSE	Close OxV1		2
378	0:00	EGSE	Open OxV2		2
379	0:00	EGSE	Confirm OxInPT2 & OxOutPT 0 Bar		2
380	0:00	EGSE	Close OxV2		2
381	0:00	EGSE	Close OxDV		2
382	0:00	MRL	Go to MRL, confirm OxInPG1 & OxInPG2 0 Bar, else RETURN to Block House, THEN...		2
383	0:00	MRL	Close He Bottle 2, THEN...		2
384	0:00	MRL	Write down remaining Pressure of He Bottle 2, THEN...		2
385	0:00	MRL	Return to Block House		2
386	0:00	EGSE	Open HPDV		2
387	0:00	EGSE	Open HPV2		2
388	0:00	EGSE	Confirm pressure HPLPT & HPPT2 0 Bar		2
389	0:00	EGSE	Close HPV2		2
390	0:00	EGSE	Close HPDV		2
391	0:00	MRL	Go to Testrig, confirm HPPG2 0 Bar, else return to Block House, THEN...		2
392	0:00	MRL	Close He Bottle 1, THEN ...		2
393	0:00	MRL	Open ComTerm		2
394	8:15	MCC	Turn ON ComTerm step delay		2
395	0:00	MRL	Write down remaining Pressure of He Bottle 1		2
396	0:00	MRL	Step back		2
397	0:00	EGSE	Open HPDV		2
398	0:00	EGSE	Open HPV1		2
399	0:00	EGSE	Confirm pressure HPLPT & HPPT1 0 Bar		2
400	0:00	EGSE	Close HPV1		2
401	0:00	EGSE	Close HPDV		2
402	0:00	EGSE	Pressure Check		2
403	0:00	MRL	Open MBV		2
404	0:00	EGSE/ MRL	Check and compare pressure HPPT1 with HPPG1		2
405	0:00	MRL	Close MBV		2
406	0:00	MRL	Take out B1 & B2 Bridges		2
407	0:00	MRL	Safety is ensured		2
408	0:00	MCC	Confirm to OPS that Safety is ensured		2
409	0:00	MCC	BEGIN SEQUENCE: Data collection	Data collection	1
410	0:00	AVC	Turn off GoPro & Camcorder & Stop Block House Video recording		1
411	0:00	EGSE	Copy PID.vi.tdms & save to new name		1
412	0:00	EGSE	Wait for buffer storage process to be finished		1
413	0:00	EGSE	save data files from cRio to PC		1
414	0:00	WIND	Save data on external HDD		1
415	0:00	TMTC	Stop TMTC Vi and save data on external HDD		1
416	0:00	AVC	End audio recording		1
417	0:00	MCC	Stop ComTerm and save logfile to external HDD, THEN...		1
418	0:00	MCC	Restart ComTerm VI		1
419	0:00	AVC	Save video & audio data on external HDD		1
420	0:00	MCC	END OF PROCEDURE	End	1