20 KiB
20 KiB
| 1 | vers. | v4.7 | Launch Procedure | 0 | MRL | MCC | RdHill | Time per step | ||
|---|---|---|---|---|---|---|---|---|---|---|
| 2 | 147:20 | MCC | BEGIN SEQUENCE: Power on EGSE | Power on EGSE | 1 | |||||
| 3 | 147:20 | EGSE | Check CLD connection | 1 | ||||||
| 4 | 147:20 | EGSE | Switch ON CLD via Battery & check voltage (24 Volt) | 1 | ||||||
| 5 | 147:20 | EGSE | Switch ON the primary and secondary supply switches on the Control Panel | 1 | 01:00 | |||||
| 6 | 146:20 | EGSE@MRL | Switch ON Sup_24V_20A & check voltage (ca. 27,2 Volt) | 1 | ||||||
| 7 | 146:20 | EGSE@MRL | Switch ON Sup_24V_10A & check voltage (ca. 27,2 Volt) | 1 | ||||||
| 8 | 146:20 | EGSE@MRL | Switch ON Sup_12V_10A & check voltage (ca. 13,8 Volt) | 1 | ||||||
| 9 | 146:20 | EGSE@MRL | Switch ON Bat_24V_20A & check voltage (ca. 27,9 Volt) | 1 | ||||||
| 10 | 146:20 | EGSE@MRL | Switch ON Bat_24V_10A & check voltage (ca. 27,9 Volt) | 1 | ||||||
| 11 | 146:20 | EGSE@MRL | Switch ON Bat_12V_10A & check voltage (ca. 13,8 Volt) | 1 | ||||||
| 12 | 146:20 | EGSE@MRL | Switch ON Sup_24V_40A | 1 | ||||||
| 13 | 146:20 | EGSE@MRL | Switch ON Sup_5V_10A | 1 | 03:00 | |||||
| 14 | 143:20 | EGSE | Connect to cRIO | 1 | ||||||
| 15 | 143:20 | EGSE | Start FPGA_VI | 1 | ||||||
| 16 | 143:20 | EGSE | Start RT_VI | 1 | ||||||
| 17 | 143:20 | EGSE | Confirm PID-VI is running | 1 | ||||||
| 18 | 143:20 | EGSE | Rename PID-Logfile | 1 | 02:00 | |||||
| 19 | 141:20 | MCC | BEGIN SEQUENCE: Connect Data Umbilical | Connect Data Umbilical | 1 | 00:30 | ||||
| 20 | 141:20 | MRL | Confirm working Personel is grounded | 1 | ||||||
| 21 | 141:20 | EGSL@MRL | Confirm all 8 Groundingbridges are inserted | 1 | ||||||
| 22 | 140:50 | EGSE | Turn on EPS_BAT | 1 | ||||||
| 23 | 140:50 | EGSE | Turn on EPS_EXT | 1 | ||||||
| 24 | 140:50 | EGSE@MRL | Leave EPS_BAT inserted and remove the other 7 Grounding Bridges | 1 | ||||||
| 25 | 140:50 | EGSE@MRL | Insert EPS_EXT Fuse in Power Supply Control Panel | 1 | ||||||
| 26 | 140:50 | EGSE@MRL | Confirm green LED at EPS_EXT Fuse is on | 1 | ||||||
| 27 | 140:50 | EGSE@MRL | Insert Main_Bus Fuse in Power Supply Control Panel | 1 | ||||||
| 28 | 140:50 | EGSE@MRL | Confirm LED at Main_Bus Fuse is OFF. Else Pull fuse and insert all Grounding Bridges | 1 | ||||||
| 29 | 140:50 | EGSE@MRL | Set remaining Fuses (except Payload Fuse) and check for green LED | 1 | ||||||
| 30 | 140:50 | EGSE | Turn OFF EPS_BAT | 1 | ||||||
| 31 | 140:50 | EGSE@MRL | Confirm Main bus LED is on. | 1 | ||||||
| 32 | 140:50 | EGSE | Start EPS via EPS_ext | 1 | ||||||
| 33 | 140:50 | OBDH | Clear SD-Card-using FileZilla FTP | 1 | 01:00 | |||||
| 34 | 139:50 | OBDH | Connect to sbRIO | 1 | ||||||
| 35 | 139:50 | OBDH | Start RT_Main | 1 | ||||||
| 36 | 139:50 | MRL | Confirm 3 beeps at OBC1 | 1 | ||||||
| 37 | 139:50 | OBDH | Open RT_Sub_HMI | 1 | ||||||
| 38 | 139:50 | OBDH | Confirm Main Chute button is disabled | 1 | ||||||
| 39 | 139:50 | EGSE@MRL | Insert Payload Fuse | 1 | ||||||
| 40 | 139:50 | EGSE@MRL | Confirm green LED at Payload Fuse is on | 1 | ||||||
| 41 | 139:50 | MCC | BEGIN SEQUENCE: Connect Fueling arm | Connect Fueling Arm | 1 | |||||
| 42 | 139:50 | MRL | Confirm working Personel is grounded | 1 | 01:00 | |||||
| 43 | 138:50 | MRL | Remove Pneumatic Line from Fueling arm | 1 | ||||||
| 44 | 138:50 | MRL | Move Fueling arm to rocket | 1 | ||||||
| 45 | 138:50 | MRL | Couple Helium coupling | 1 | ||||||
| 46 | 138:50 | MRL | Couple N2O coupling | 1 | ||||||
| 47 | 138:50 | MRL | Reattach Pneumatic Line to Fueling arm | 1 | 03:00 | |||||
| 48 | 135:50 | EGSE | BEGIN SEQUENCE: EGSE Valve and Actuator check | EGSE Valve & Actuator Check | 1 | |||||
| 49 | 135:50 | MCC | Confirm that video recording is enabled @ MCC | 1 | 00:10 | |||||
| 50 | 135:50 | MRL | Confirm that Ignition Umbilical is disconnected | 1 | ||||||
| 51 | 135:40 | OBDH | Check EPS hardware Voltages | 1 | 00:10 | |||||
| 52 | 135:30 | EGSE | Start PID data recording | 1 | 00:10 | |||||
| 53 | 135:20 | MRL | Close HPNV | 1 | 00:10 | |||||
| 54 | 135:10 | EGSE/MRL | Switch OxDV to closed & check if magnetic valve LED is on | 1 | 00:10 | |||||
| 55 | 135:00 | EGSE/MRL | Switch HPDV to closed & check if magnetic valve LED is on | 1 | 00:10 | |||||
| 56 | 134:50 | EGSE/MRL | Check warning lamp on HPSM | 1 | 00:10 | |||||
| 57 | 134:40 | MRL | Remove loose equipment | 1 | 03:00 | |||||
| 58 | 131:40 | EGSE | Activate Heizi | 1 | 00:10 | |||||
| 59 | 131:30 | EGSE | Activate N2O_Heater 1 | 1 | 00:10 | |||||
| 60 | 131:20 | EGSE | Activate N2O_Heater 2 | 1 | 00:10 | |||||
| 61 | 131:10 | EGSE | Activate He_Heater | 1 | 00:10 | |||||
| 62 | 131:00 | OBDH | Verify Heizi @ RDVT & RDVET | 1 | 00:10 | |||||
| 63 | 130:50 | EGSE/MRL | Verify Bottle Temperatures @ OxT1, OxT2, HPT2 | 1 | 00:10 | |||||
| 64 | 130:40 | EGSE/MRL | Verify Water Temperatures @ Ox@T1, OxWT2, HPWT2 | 1 | 00:10 | |||||
| 65 | 130:30 | EGSE | Deactivate Heizi | 1 | 00:10 | |||||
| 66 | 130:20 | EGSE | Check OxV1 (CLD & RT_VI) | 1 | 00:10 | |||||
| 67 | 130:10 | EGSE | Check OxV2 (CLD & RT_VI) | 1 | 00:10 | |||||
| 68 | 130:00 | EGSE | Check MPV3 (CLD & RT_VI) | 1 | 00:10 | |||||
| 69 | 129:50 | EGSE | Check HPV1 (CLD & RT_VI) | 1 | 00:10 | |||||
| 70 | 129:40 | EGSE | Check HPV2 (CLD & RT_VI) | 1 | 00:10 | |||||
| 71 | 129:30 | EGSE | Check MPV1/2 (CLD & RT_VI) | 1 | 00:10 | |||||
| 72 | 129:20 | EGSE | Check RDV (CLD & RT_VI) | 1 | 00:10 | |||||
| 73 | 129:10 | EGSE | Check RMOxOV (CLD & RT_VI) | 1 | 00:10 | |||||
| 74 | 129:00 | EGSE | Check RMOxSV (CLD & RT_VI) | 1 | 00:10 | |||||
| 75 | 128:50 | OBDH | Activate Heizi | 1 | 00:10 | |||||
| 76 | 128:40 | OBDH | Verify Heizi @ RDVT & RDVET | 1 | 01:00 | |||||
| 77 | 127:40 | OBDH | Check RDV | 1 | 00:10 | |||||
| 78 | 127:30 | OBDH | Check RNCEV | 1 | 00:10 | |||||
| 79 | 127:20 | OBDH | Check RMOxOV | 1 | 00:10 | |||||
| 80 | 127:10 | OBDH | Check RMOxSV | 1 | 00:10 | |||||
| 81 | 127:00 | OBDH | Confirm RNCEV is disabled | 1 | 00:10 | |||||
| 82 | 125:00 | MRL | Confirm MBV closed | 1 | ||||||
| 83 | 125:00 | EGSE | Confirm that all valve switches are in OFF position (Except OxDV & HPDV) | 1 | 0:10 | |||||
| 84 | 115:00 | MRL/EGSE | Check loadcell by applying force to it | 1 | 00:20 | |||||
| 85 | 114:40 | OBDH | Check RHPPT shows atmosphere | 1 | ||||||
| 86 | 114:40 | OBDH | Check ROxTPT shows atmosphere | 1 | ||||||
| 87 | 114:40 | OBDH | Check RIHPT shows atmosphere | 1 | ||||||
| 88 | 114:40 | OBDH | Check RCCPT shows atmosphere | 1 | ||||||
| 89 | 114:40 | OBDH | Check RBaro1 shows atmosphere | 1 | ||||||
| 90 | 114:40 | OBDH | Check RBaro2 shows atmosphere | 1 | ||||||
| 91 | 114:40 | EGSE | Check HPPT1 shows 0 bar | 1 | 00:20 | |||||
| 92 | 114:20 | EGSE | Check HPPT2 shows 0 bar | 1 | ||||||
| 93 | 114:20 | EGSE | Check HPLPT shows 0 bar | 1 | ||||||
| 94 | 114:20 | EGSE | Check OxInPT1 shows 0 bar | 1 | ||||||
| 95 | 114:20 | EGSE | Check OxInPT2 shows 0 bar | 1 | ||||||
| 96 | 114:20 | EGSE | Check OxOutPT shows 0 bar | 1 | 00:20 | |||||
| 97 | 114:00 | EGSE/MRL | Switch on N2O coupling & check if magnetic valve LED is on | 1 | ||||||
| 98 | 114:00 | EGSE/MRL | Switch on He coupling & check if magnetic valve LED is on | 1 | ||||||
| 99 | 114:00 | EGSE/MRL | Switch on swivle arm & check if magnetic valve LED is on | 1 | ||||||
| 100 | 114:00 | EGSE | Switch off swivel arm & He coupling & N2O coupling | 1 | 01:00 | |||||
| 101 | 114:00 | MCC | BEGIN SEQUENCE: Ignition signal Test | Ignition signal Test | 1 | 01:00 | ||||
| 102 | 113:00 | MRL | Confirm that Ignition Umbilical is disconnected | 1 | ||||||
| 103 | 113:00 | MRL | Connect Ignition test receptical | 1 | ||||||
| 104 | 113:00 | EGSE@MRL | Plug in Bridges B1 and B2 | 1 | ||||||
| 105 | 113:00 | MRL | Confirm Soundsignal from Ignition Umbilical | 1 | ||||||
| 106 | 113:00 | EGSE | Turn on Ignition Secure Switch | 1 | ||||||
| 107 | 113:00 | EGSE/OBDH | Turn on Ignition Switch for 2 Second & Confirm ignition signal received at sbRio | 1 | ||||||
| 108 | 113:00 | EGSE/OBDH | Confirm that Ignition Switch is switched off | 1 | ||||||
| 109 | 113:00 | EGSE | Turn off Ignition Secure Switch | 1 | ||||||
| 110 | 113:00 | EGSE@MRL | Remove Bridges B1 and B2 | 1 | ||||||
| 111 | 113:00 | MRL | Remove Ignition test receptical | 1 | 03:00 | |||||
| 112 | 110:00 | MCC | BEGIN SEQUENCE: pneumatic pressure test (PHASE YELLOW) | Pneumatic Pressure Test | 1 | |||||
| 113 | 110:00 | EGSE/MRL | Verify Bottle Temperatures @ OxT1, OxT2, HPT2 | 1 | 00:10 | |||||
| 114 | 110:00 | EGSE/MRL | Verify Water Temperatures @ Ox@T1, OxWT2, HPWT2 | 1 | 00:10 | |||||
| 115 | 110:00 | MRL | Confirm that all hatches are closed | 1 | 01:00 | |||||
| 116 | 109:00 | MRL | Check He bottle 1 connector is attached | 1 | ||||||
| 117 | 109:00 | MRL | Check He bottle 2 connector is attached | 1 | ||||||
| 118 | 109:00 | MRL | Check N2O bottle 1 connector is attached | 1 | ||||||
| 119 | 109:00 | MRL | Check N2O bottle 2 connector is attached | 1 | ||||||
| 120 | 109:00 | MRL | Check hose between HPSM & N2OSM is connected on both ends | 1 | ||||||
| 121 | 109:00 | MRL | Check hose between HPSM & Flight Segment is connected on both ends | 1 | ||||||
| 122 | 109:00 | MRL | Check hose between N2OSM & Flight Segment is connected on both ends | 1 | ||||||
| 123 | 109:00 | MRL | Check Pneumatik hose is connected on both ends | 1 | 02:00 | |||||
| 124 | 107:00 | MRL | Put on safety equipment | 2 | ||||||
| 125 | 107:00 | MRL | Move into Position to open He Bottle 1 | 2 | ||||||
| 126 | 107:00 | MRL | Confirm MBV is closed | 2 | ||||||
| 127 | 107:00 | EGSE | Confirm if HPV1 is closed | 2 | ||||||
| 128 | 107:00 | EGSE | Confirm MPV1/2 is closed | 2 | ||||||
| 129 | 107:00 | MRL | Open He Bottle 1 | 2 | 01:00 | |||||
| 130 | 106:00 | MRL | Check & compare pressure HPPT1 with HPPG1 (max 300 bar) | 2 | ||||||
| 131 | 106:00 | MRL | Check Gastech Silver HPPR1 (max 300 to 50 bar) | 2 | ||||||
| 132 | 106:00 | MRL | Check Harris PPR (50 to 8 bar) | 2 | ||||||
| 133 | 106:00 | MRL | Check pneumatic PPG (8 bar) | 2 | ||||||
| 134 | 106:00 | MRL | Step back | 2 | 01:00 | |||||
| 135 | 105:00 | EGSE/MRL | Open & Close HPV1 SHORTLY & Check HPPT1 | 2 | ||||||
| 136 | 105:00 | EGSE | Confirm HPPT1 is at 300 Bar | 2 | ||||||
| 137 | 105:00 | EGSE | Confirm HPLPT less than 10 Bar | 2 | ||||||
| 138 | 105:00 | EGSE/MRL | Open & Close HPV2 SHORTLY & Check HPPT2 0 bar | 2 | ||||||
| 139 | 105:00 | EGSE/MRL | Open & Close HPDV SHORTLY & Check HPLPT 0 bar | 2 | ||||||
| 140 | 105:00 | EGSE/MRL | Open & Close OxV1 SHORTLY | 2 | ||||||
| 141 | 105:00 | EGSE/MRL | Open & Close OxV2 SHORTLY | 2 | ||||||
| 142 | 105:00 | EGSE/MRL | Open & Close OxDV SHORTLY | 2 | ||||||
| 143 | 105:00 | EGSE/MRL | Open & Close MPV3 SHORTLY | 2 | ||||||
| 144 | 105:00 | EGSE | Check HPLPT & OxOutPT 0 Bar | 2 | 01:30 | |||||
| 145 | 103:30 | EGSE | Decouple N2O coupling | 2 | ||||||
| 146 | 103:30 | EGSE | Decouple Helium coupling | 2 | 00:20 | |||||
| 147 | 103:10 | EGSE | Move arm away from rocket | 2 | ||||||
| 148 | 103:10 | EGSE | Move arm to rocket | 2 | 01:00 | |||||
| 149 | 102:10 | MRL | Close He Bottle 1 and check HPSM for leakage (If leakage occurs Abort) | 2 | 01:00 | |||||
| 150 | 101:10 | MRL | Open HPNV 1/8 Rev | 2 | ||||||
| 151 | 101:10 | MRL | Open MBV | 2 | ||||||
| 152 | 101:10 | EGSE/MRL | Check and compare pressure HPPT1 with HPPG1 0 Bar | 2 | ||||||
| 153 | 101:10 | MRL | Close MBV | 2 | 00:30 | |||||
| 154 | 100:40 | MRL | Safety is ensured | 2 | ||||||
| 155 | 100:40 | MCC | MiS to MRL | 1 | ||||||
| 156 | 100:40 | EGSE | Switch OFF N20 coupling | 1 | ||||||
| 157 | 100:40 | EGSE | Switch OFF He coupling | 1 | ||||||
| 158 | 100:40 | MRL | Confirm working Personel is grounded | 1 | 01:00 | |||||
| 159 | 100:40 | MRL | Release Pneumatic lines of couplings | 1 | 00:20 | |||||
| 160 | 100:20 | EGSE | Confirm Fueling arm is switched OFF | 1 | ||||||
| 161 | 100:20 | EGSE | Check OxOutPT and HPLPT 0 bar | 1 | ||||||
| 162 | 100:20 | MRL | Couple He coupling | 1 | 00:30 | |||||
| 163 | 99:50 | MRL | Couple N2O coupling | 1 | 00:30 | |||||
| 164 | 99:50 | MRL | Confirm He coupling is connected properly | 1 | ||||||
| 165 | 99:50 | MRL | Confirm N2O coupling is connected properly | 1 | ||||||
| 166 | 99:20 | MRL | HOLD | HOLD | 1 | |||||
| 167 | 99:20 | EGSE/MRL | Verify Bottle Temperatures @ OxT1, OxT2, HPT2 | 1 | 00:10 | |||||
| 168 | 99:20 | EGSE/MRL | Verify Water Temperatures @ Ox@T1, OxWT2, HPWT2 | 1 | 00:10 | |||||
| 169 | 99:20 | MCC | CONTINUE AFTER HOLD | |||||||
| 170 | 99:20 | MRL | BEGIN SEQUENCE: Arming Rocket Part 1 | Arming Rocket Pt.1 | 1 | |||||
| 171 | 99:20 | MRL | Confirm working Personel is grounded | 1 | 01:00 | |||||
| 172 | 99:20 | MRL | Confirm all spring retracted hatches are moving freely | 1 | ||||||
| 173 | 98:50 | MRL | Turn on GoPro Camera at end of Launch Rail | 1 | 00:20 | |||||
| 174 | 99:20 | MRL | Connect Ignition Umbilical | 1 | 00:30 | |||||
| 175 | 98:30 | MRL | Insert all EPS Bridges | 1 | 03:00 | |||||
| 176 | 95:30 | MRL | Confirm Bridge Hatch is Secured | 1 | 00:20 | |||||
| 177 | 95:10 | EGSE@MRL | return to MCC | 1 | ||||||
| 178 | 95:10 | OPS | Elevate MRL to 90 degrees | 1 | 05:00 | |||||
| 179 | 90:10 | EGSE | Powercycle EPS to to start flight mode on Telemega | 1 | 00:30 | |||||
| 180 | 89:40 | EGSE | Calibrate loadcell (Set to 0) | 1 | 01:00 | |||||
| 181 | 88:40 | MCC | BEGIN SEQUENCE: Fueling Preparations (PHASE YELLOW) | Fueling Preparations | 2 | |||||
| 182 | 89:40 | EGSE/MRL | Verify Bottle Temperatures @ OxT1, OxT2, HPT2 | 1 | 00:10 | |||||
| 183 | 89:40 | EGSE/MRL | Verify Water Temperatures @ Ox@T1, OxWT2, HPWT2 | 1 | 00:10 | |||||
| 184 | 88:40 | MRL | Put on safety equipment | 2 | 00:30 | |||||
| 185 | 88:10 | MRL | Open He Bottle 1 | 2 | 01:00 | |||||
| 186 | 87:10 | MRL | Step back | 2 | ||||||
| 187 | 87:10 | EGSE | Open & Close STEPWISE MPV1/MPV2 to 50 Bar @ OxInPT1 & OxInPT2 | 2 | ||||||
| 188 | 87:10 | EGSE/MRL | Check & compare OxInPT1 with OxInPG1 based on Bottle temperature (max 50 bar) | 2 | ||||||
| 189 | 87:10 | EGSE/MRL | Check & compare pressure OxInPT2 with OxInPG2 based on Bottle temperature (max 50 bar) | 2 | ||||||
| 190 | 87:10 | EGSE/MRL | Check Temperature of N2O Bottle 1 @OxT1 & OxWT1 (max 22C) | 2 | ||||||
| 191 | 87:10 | EGSE/MRL | Check Temperature of N2O Bottle 2 @OxT2 & OxWT2 (max 22C) | 2 | 01:30 | |||||
| 192 | 85:40 | MRL | Open He Bottle 2 | 2 | ||||||
| 193 | 85:40 | EGSE/MRL | Check & compare pressure HPPT2 with HPPG2 (max 315 bar) | 2 | 01:00 | |||||
| 194 | 84:40 | ALL/MRL | CAUTION! | 2 | ||||||
| 195 | 84:40 | MRL | Open N2O Bottle 1 | 2 | ||||||
| 196 | 84:40 | MRL/EGSE | Check & compare pressure OxInPT 1 with OxInPG 1 (max 50 bar) | 2 | 02:00 | |||||
| 197 | 82:40 | MRL | Open N2O Bottle 2 | 2 | ||||||
| 198 | 82:40 | MRL/EGSE | Check & compare pressure OxInPT 2 with OxInPG 2 (max 50 bar) | 2 | 02:00 | |||||
| 199 | 80:40 | MRL | Insert Ignition Bridges B1 and B2 into EGSE | 2 | 02:00 | |||||
| 200 | 78:40 | MRL | Confirm Soundsignal from Ignition Umbilical | 2 | ||||||
| 201 | 78:40 | MRL | Close ComTerm | 2 | ||||||
| 202 | 78:40 | MCC | Turn Off MRL lock | 2 | ||||||
| 203 | 78:40 | ALL | Clear Launchpad and inform OPS | 2 | 10:00 | |||||
| 204 | 68:40 | KLP | Start Camera Karsten Lapp<70>hn | 2 | ||||||
| 205 | 68:40 | MCC | HOLD | HOLD | 2 | |||||
| 206 | 68:40 | EGSE | Verify Bottle Temperatures @ OxT1, OxT2, HPT2 | 1 | 00:10 | |||||
| 207 | 68:40 | EGSE | Verify Water Temperatures @ Ox@T1, OxWT2, HPWT2 | 1 | 00:10 | |||||
| 208 | 68:40 | MCC | CONTINUE AFTER HOLD | |||||||
| 209 | 68:40 | MCC | BEGIN SEQUENCE Ox Fueling (PHASE RED) | Ox Fueling (PHASE RED) | 3 | |||||
| 210 | 68:40 | MCC | Announce end of Radio Silence | 3 | ||||||
| 211 | 68:40 | OBDH/TMTC | Check RF451-Link | 1 | 00:20 | |||||
| 212 | 68:40 | TMTC | Confirm GPS-lock | 1 | 00:20 | |||||
| 213 | 68:40 | TMTC | Confirm Telemega-Link | 1 | 00:20 | |||||
| 214 | 68:40 | OBDH | Test Connection to STX3 | 1 | 00:20 | |||||
| 215 | 68:40 | OBDH | Confirm that STX3 Package received by email | 1 | 00:30 | |||||
| 216 | 68:40 | MCC | Request Permission to begin fueling from OPS | 1 | 03:00 | |||||
| 217 | 68:40 | OBDH | Acknowledge start of Fueling | 3 | 01:00 | |||||
| 218 | 67:40 | EGSE | Open & Close HPV1 STEPWISE to 50 Bar @ ROxTPT (stop at 30 bar and wait 30 seconds to check for leakage) | 3 | ||||||
| 219 | 67:40 | EGSE | Open & Close HPV1 STEPWISE to more than 50 Bar @ RHPPT and check ROxTPT 50 Bar | 3 | ||||||
| 220 | 67:40 | EGSE | Check if HPV1 is closed | 3 | ||||||
| 221 | 67:40 | OBDH | Open RDV SHORTLY, to check tightness @ RHPPT & ROxTPT (If leakages occur Abort) | 3 | ||||||
| 222 | 67:40 | EGSE | Open MPV1/MPV2 | 3 | ||||||
| 223 | 67:40 | EGSE | Open & Close MPV3 STEPWISE to 50 Bar @ OxOutPT | 3 | ||||||
| 224 | 67:40 | EGSE | Close MPV1/MPV2 | 3 | ||||||
| 225 | 67:40 | EGSE | Check & compare OxOutPT with OxInPT1 | 3 | ||||||
| 226 | 67:40 | EGSE | Check if RHPPT & ROxTPT more than OxInPT1, If less Open & Close HPV1 | 3 | ||||||
| 227 | 67:40 | EGSE | Zero OxTank Mass | 3 | ||||||
| 228 | 67:40 | MCC | Write down Time | 3 | ||||||
| 229 | 67:40 | EGSE | Open OxV1 | 3 | 04:00 | |||||
| 230 | 63:40 | OBDH | Open & Close RDV STEPWISE until N2O bottle empty or 25kg OxTankMass, keep temperatures RDVT and RDVET above 10<31>C and Check delta ROxTPT and OxInPT1 | 3 | 30:00 | |||||
| 231 | 33:40 | EGSE | Verify Bottle Temperatures @ OxT1, OxT2, HPT2 | 1 | 00:10 | |||||
| 232 | 33:40 | EGSE | Verify Water Temperatures @ Ox@T1, OxWT2, HPWT2 | 1 | 00:10 | |||||
| 233 | 33:40 | EGSE | Close OxV1 | 3 | 00:10 | |||||
| 234 | 33:30 | EGSE | Check if Pressure rises in OxPT1, if Pressure rises relief via OxV1 or wait for Pressure relief valve | 3 | 01:00 | |||||
| 235 | 32:30 | EGSE | Check & compare OxOutPT with OxInPT2 | 3 | ||||||
| 236 | 32:30 | EGSE | Check & compare RHPPT & ROxTPT 50 Bar and more than OxInPT2, If less Open & Close HPV1 | 3 | ||||||
| 237 | 32:30 | EGSE | Open OxV2 | 3 | ||||||
| 238 | 32:30 | OBDH | Open & Close RDV STEPWISE to 25kg OxTankMass, keep temperatures RDVT and RDVET above 10<31>C and Check delta OxTPT and OxInPT1 | 3 | 20:00 | |||||
| 239 | 12:30 | EGSE | Close OxV2 | 3 | 00:10 | |||||
| 240 | 12:20 | EGSE | Check if Pressure rises in OxPT2, if Pressure rises relief via OxV2 or wait for Pressure relief valve | 3 | 01:00 | |||||
| 241 | 11:20 | EGSE | Open OxDV STEPWISE until OxOutPT 0 Bar | 3 | ||||||
| 242 | 11:20 | OBDH | Check ROxCV for tightness @ ROxTPT | 3 | ||||||
| 243 | 11:20 | EGSE | Close OxDV | 3 | 01:00 | |||||
| 244 | 10:20 | EGSE | Write down OxTankMass | 3 | ||||||
| 245 | 10:20 | MCC | Provide OxTankMass and temperature readings to Wind weighting station | 3 | 00:30 | |||||
| 246 | 9:50 | EGSE | Confirm OxV1 & OxV2 closed | 3 | ||||||
| 247 | 9:50 | EGSE | Check OxOutPT 0 Bar | 3 | ||||||
| 248 | 9:50 | EGSE | Decouple N2O coupling | 3 | 00:20 | |||||
| 249 | 9:30 | MCC | Confirm End of Oxidator Fueling to OPS | 3 | 00:15 | |||||
| 250 | 9:15 | OBDH/TMTC | Check RF451-Link | 3 | 00:20 | |||||
| 251 | 8:55 | TMTC | Check GPS-lock | 3 | 00:20 | |||||
| 252 | 8:35 | TMTC | Check Telemega-Link | 3 | 00:20 | |||||
| 253 | 8:15 | MCC | HOLD | HOLD | 3 | |||||
| 254 | 8:15 | OPS | Align MRL to Launch Trajectory | 3 | ||||||
| 255 | 8:15 | MCC | Turn audio volume down | 3 | ||||||
| 256 | 8:15 | MCC | Turn off Confirm delay | 3 | ||||||
| 257 | 8:15 | ALL | Talk through Launch Sequence | 3 | ||||||
| 258 | 8:15 | MCC | Confirm MRL adjustment with OPS | 3 | ||||||
| 259 | 8:15 | AVC | Start Video recording in Block House | 3 | ||||||
| 260 | 8:15 | MCC | CONTINUE AFTER HOLD | |||||||
| 261 | 8:15 | MCC | BEGIN Switching to Internal Power Sequence | Switch to Internal Power | 3 | |||||
| 262 | 8:15 | EGSE | Switch to internal Power | 3 | 00:20 | |||||
| 263 | 7:55 | OBDH | Confirm EPS Voltages are within limits | 3 | 00:10 | |||||
| 264 | 7:45 | OBDH | Confirm RF451 Transmitting | 3 | 00:05 | |||||
| 265 | 7:40 | OBDH/TMTC | Confirm RF451-Link | 3 | 00:20 | |||||
| 266 | 7:20 | TMTC | Confirm GPS-lock | 3 | 00:20 | |||||
| 267 | 7:00 | TMTC | Confirm Telemega-Link | 3 | 00:20 | |||||
| 268 | 6:40 | OBDH | Switch to PREAMRED | 3 | 00:10 | |||||
| 269 | 6:30 | PYL | Confirm Payload is running | 3 | 00:20 | |||||
| 270 | 6:10 | AVC | Confirm that videorecording @ MCC is running | 3 | 00:05 | |||||
| 271 | 6:05 | MCC | BEGIN SEQUENCE: High Pressure Fueling | High Pressure Fueling | 3 | |||||
| 272 | 6:05 | EGSE | Open & Close HPV1 STEPWISE until RHPPT 300 Bar or pressure equal to He Bottle 1 | 3 | ||||||
| 273 | 6:05 | EGSE | Open & Close HPV2 STEPWISE until RHPPT 300 Bar | 3 | ||||||
| 274 | 6:05 | EGSE | Open & close HPDV STEPWISE until HPLPT 0 Bar | 3 | ||||||
| 275 | 6:05 | EGSE | Confirm HPDV closed | 3 | ||||||
| 276 | 6:05 | OBDH/EGSE | Check for leakage & HPLPT 0 Bar & RHPPT 300 Bar | 3 | 02:00 | |||||
| 277 | 4:05 | OBDH | Acknowledge end of Fueling | 3 | 00:10 | |||||
| 278 | 3:55 | MCC | Confirm End of Fueling to OPS | 3 | 00:20 | |||||
| 279 | 3:35 | MCC | BEGIN SEQUENCE: Disconnecting Fueling Arm | Disconnecting Fueling Arm | 3 | 00:10 | ||||
| 280 | 3:25 | EGSE | Confirm HPV1 & HPV2 closed | 3 | 00:10 | |||||
| 281 | 3:15 | EGSE | Check HPLPT 0 Bar | 3 | 00:10 | |||||
| 282 | 3:05 | EGSE | Decouple Helium coupling | 3 | 00:20 | |||||
| 283 | 2:45 | EGSE | Confirm Helium coupling is disconnected | 3 | 00:10 | |||||
| 284 | 2:35 | EGSE | Move fueling arm away from rocket | 3 | 00:40 | |||||
| 285 | 1:55 | MCC | Confirm Fueling Arm away to OPS | 3 | 00:15 | |||||
| 286 | 1:40 | MCC | Prepare for Launch | 3 | 00:10 | |||||
| 287 | 1:30 | OBDH | Confirm ready for launch | 3 | 00:10 | |||||
| 288 | 1:20 | EGSE | Confirm ready for launch | 3 | 00:10 | |||||
| 289 | 1:10 | MCC | Set Go/No-Go System to Go | 3 | 00:10 | |||||
| 290 | 1:00 | MCC | Wait for Authorization for Launch | 3 | 00:00 | |||||
| 291 | 1:00 | MCC | BEGIN SEQUENCE: Ignition | Ignition Sequence | 4 | 00:10 | ||||
| 292 | 0:50 | OBDH | ARM | 4 | 00:05 | |||||
| 293 | 0:45 | OBDH | Confirm all status indicators green | 4 | 00:05 | |||||
| 294 | 0:40 | OBDH | Disconnect Ethernet | 4 | 00:30 | |||||
| 295 | 0:10 | EGSE | Turn on Ignition Secure | 4 | 00:07 | |||||
| 296 | 0:03 | EGSE | T-3: Ignition | 4 | 00:03 | |||||
| 297 | 0:00 | OBDH | T+0: Verify RMOxOV Open (Launched) | 4 | 00:00 | |||||
| 298 | 0:00 | EGSE | T+1: Turn OFF Ignition | 4 | ||||||
| 299 | 0:00 | EGSE | T+5: Turn OFF Ignition Secure | 4 | ||||||
| 300 | 0:00 | OBDH | T+20: Verify RMOxOV Closed and RMOxSV Open (Cruise) | 4 | ||||||
| 301 | 0:00 | OBDH | T+50: Verify RNCEV Open (Drogue) | 4 | ||||||
| 302 | 0:00 | OBDH | T+310: Verify Main Chute Deployed and RDV Open (Main) | 4 | ||||||
| 303 | 0:00 | OBDH | T+600: Verify (Landed) | 4 | ||||||
| 304 | 0:00 | MCC | BEGIN SEQUENCE: PASSIVATION (PHASE YELLOW) (Write down Time) | Passivation | 2 | |||||
| 305 | 68:40 | MCC | Announce BEGIN of Radio Silence | 3 | ||||||
| 306 | 0:00 | MCC | Turn audio volume up | 2 | ||||||
| 307 | 0:00 | TMTC | Check ROxTPT & RHPPT 1 Bar, if more: Open & Close STEPWISE RDV | 2 | ||||||
| 308 | 0:00 | MRL | Go to Testrig, Close N2O Bottle 1 & N2O Bottle 2 then RETURN to Block House | 2 | ||||||
| 309 | 0:00 | EGSE | Open OxDV | 2 | ||||||
| 310 | 0:00 | EGSE | Open OxV1 | 2 | ||||||
| 311 | 0:00 | EGSE | Check OxInPT1 & OxOutPT 0 Bar | 2 | ||||||
| 312 | 0:00 | EGSE | Close OxV1 | 2 | ||||||
| 313 | 0:00 | EGSE | Open OxV2 | 2 | ||||||
| 314 | 0:00 | EGSE | Check OxInPT2 & OxOutPT 0 Bar | 2 | ||||||
| 315 | 0:00 | EGSE | Close OxV2 | 2 | ||||||
| 316 | 0:00 | EGSE | Close OxDV | 2 | ||||||
| 317 | 0:00 | MRL | Close He Bottle 2, THEN... | 2 | ||||||
| 318 | 0:00 | MRL | Write down remaining Pressure of He Bottle 2, THEN... | 2 | ||||||
| 319 | 0:00 | MRL | Return to Block House | 2 | ||||||
| 320 | 0:00 | EGSE | Open HPDV | 2 | ||||||
| 321 | 0:00 | EGSE | Open HPV2 | 2 | ||||||
| 322 | 0:00 | EGSE | Check pressure HPLPT & HPPT2 0 Bar | 2 | ||||||
| 323 | 0:00 | EGSE | Close HPV2 | 2 | ||||||
| 324 | 0:00 | EGSE | Close HPDV | 2 | ||||||
| 325 | 0:00 | MRL | Go to Testrig, confirm HPPG2 0 Bar, else return to Block House, THEN... | 2 | ||||||
| 326 | 0:00 | MRL | Close He Bottle 1, THEN ... | 2 | ||||||
| 327 | 0:00 | MRL | Open ComTerm | 2 | ||||||
| 328 | 0:00 | MCC | Turn on MRL lock | 2 | ||||||
| 329 | 0:00 | MRL | Write down remaining Pressure of He Bottle 1 | 2 | ||||||
| 330 | 0:00 | MRL | Step back | 2 | ||||||
| 331 | 0:00 | EGSE | Open HPDV | 2 | ||||||
| 332 | 0:00 | EGSE | Open HPV1 | 2 | ||||||
| 333 | 0:00 | EGSE | Check pressure HPLPT & HPPT1 0 Bar | 2 | ||||||
| 334 | 0:00 | EGSE | Close HPV1 | 2 | ||||||
| 335 | 0:00 | EGSE | Close HPDV | 2 | ||||||
| 336 | 0:00 | EGSE | Pressure Check | 2 | ||||||
| 337 | 0:00 | MRL | Open MBV | 2 | ||||||
| 338 | 0:00 | EGSE/MRL | Check and compare pressure HPPT1 with HPPG1 | 2 | ||||||
| 339 | 0:00 | MRL | Close MBV | 2 | ||||||
| 340 | 0:00 | MRL | Take out B1 & B2 Bridges | 2 | ||||||
| 341 | 0:00 | MRL | Safety is ensured | 2 | ||||||
| 342 | 0:00 | MCC | Confirm to OPS that Safety is ensured | 1 | ||||||
| 343 | 0:00 | MCC | BEGIN SEQUENCE: Data collection | Data collection | 1 | |||||
| 344 | 0:00 | AVC | Turn off GoPro & Camcorder & Stop Block House Video recording | 1 | ||||||
| 345 | 0:00 | EGSE | Copy PID.vi.tdms & save to new name | 1 | ||||||
| 346 | 0:00 | EGSE | Wait for buffer storage process to be finished | 1 | ||||||
| 347 | 0:00 | EGSE | save data files from cRIO to PC | 1 | ||||||
| 348 | 0:00 | AVC | End audio recording | 1 | ||||||
| 349 | 0:00 | MCC | Stop ComTerm and save logfile to external HDD, THEN... | 1 | ||||||
| 350 | 0:00 | MCC | Restart ComTerm VI | 1 | ||||||
| 351 | 0:00 | AVC | Save video & audio data on external HDD | 1 | ||||||
| 352 | 0:00 | MCC | END OF PROCEDURE | 1 |